Results 1 to 1 of 1

Thread: xCam / Mcas Installer V1.0 by KinkDink - Octagon HD

  1. #1
    VIP Member
    Join Date
    04-03-2009
    Posts
    5,494
    Uploads
    980

    xCam / Mcas Installer V1.0 by KinkDink - Octagon HD

    xCam / Mcas Installer V1.0 by KinkDink

    For ICECRYPT S4000 HD PVR and OCTAGON S1018HD PVR Receivers.

    -------------------------------------
    Firmware Requirements
    -------------------------------------
    ICECRYPT S4000 HD PVR Firmware Version: v1.07.94 or above.
    OCTAGON SF1018 HD ALLIANCE V1.07.94 or above.

    -------------------------------
    Installer Instructions
    -------------------------------
    First, get the IP address of your receiver. To do this:
    Press Menu --> Installation --> Network Settings --> change DHCP off and then ON

    You will then get an IP number.

    Unzip all the files including all the folders in this zip to your local HDD.
    Be sure to tick the box "Use Folder Names" or "Extract Full Paths" depending on your Zip Utility.
    File structure should look like this on your Hard Disk after unzipping.

    xCam_Mcas_Installer.exe
    README.txt
    Mcas (folder)
    xCam (folder)

    If you don't see the folders then you've unzipped the files incorrectly.

    -----------------------------------------------------------------------------
    Editing cardclient.conf Instructions for xCam
    -----------------------------------------------------------------------------

    Edit the cardclient.conf file in the /xCam/var/etc folder and add your C line.
    Use a suitable text editor like wordpad to do this then save the file.

    Example, to add a C Line you'd enter the following

    cccam2:server_address.comort_nu mber:0/0/0:usernameassword

    To make it simpler, lets say:
    my server URL is server_address.com
    My port number is 12000
    My username is: kinkdink
    My password is: satdudez

    My C Line would look like this in cardclient.conf

    cccam2:server_address.com:12000:0/0/0:kinkdink:satdudez


    ----------------------------------------------
    Installing the files Instructions
    ----------------------------------------------

    Now run the xCam_Installer.exe application.

    Enter the IP address of your ICECRYPT S4000HD or OCTAGON SF1018HD Receiver into the IP Address box.
    Unless you have changed the password of your receiver leave the password box blank.
    If you have added a password to your receiver then enter that password into the password box.
    Click on the INSTALL button to FTP the files to the Receiver.

    When all files have successfully transferred, power off the receiver (power switch on the back)
    to reboot, then power on.

    In Receiver Menu:


    Press Menu --> Utilities --> CAS --> Plugin --> OK Button
    XcamClient plugin will be listed, this is the CCcam plugin.
    XcamConfigure plugin will be listed, this is for editing C lines direct from the menu using the remote control.
    Mcas plugin will be listed, this is a multi-crypt emulator and multi-crypt card reader.
    Keditor plugin will be listed, this is for editing keys direct from the menu using the remote control.

    Highlight the plugin you want to start and Press the GREEN button.


    xCam_Mcas.jpg
    Attached Files Attached Files

Similar Threads

  1. puis-je installer mbox ?
    By fernando25 in forum French / Français
    Replies: 2
    Last Post: 10-06-2009, 08:40:08
  2. comment installer les plugins sur un DM?
    By neo29200 in forum French / Français
    Replies: 1
    Last Post: 20-05-2009, 09:30:29
  3. Installer tomtom sur pda/gps
    By passete in forum French / Français
    Replies: 1
    Last Post: 16-01-2008, 01:04:02
  4. installer aes
    By ze89 in forum French / Français
    Replies: 1
    Last Post: 30-09-2006, 10:28:35

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •