Results 1 to 3 of 3

Thread: looking for linux (tuxbox) developpers

  1. #1
    VIP Member arabeman14's Avatar
    Join Date
    in front of my PC

    looking for linux (tuxbox) developpers


    I was off, Sorry for that I was busy.

    Infact I've spent my free time to make an enigma1 image for my dbox2 (tuxbox).
    Currently, it is just an FTA image (and also a beta). Multicam, and emu are not supported. But it run well

    Please do not hesitate if you can help me to get it running better and supporting emu ;)

    Best Regards

  2. #2
    VIP Member arabeman14's Avatar
    Join Date
    in front of my PC

    Re: looking for linux (tuxbox) developpers


    You can found it here:

    I'm still getting some error msg on a debug mode:

    this one is not critical:
    verify sig: 262
    Branching to 0x40000
    U-Boot 2009.08 (Tuxbox) (mai 27 2010 - 07:47:45)
    CPU:   PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
    Board: DBOX2, Nokia, BMon V1.0
           Watchdog enabled
    I2C:   ready
    DRAM:  32 MB
    FLASH:  8 MB
    Scanning JFFS2 FS: . done.
    find_inode failed for name=boot.conf
    load: Failed to find inode
    FB:    ready
    In:    serial
    Out:   serial
    Err:   serial
    LCD:   ready
    find_inode failed for name=logo-lcd
    load: Failed to find inode
    ready - can't find logo in flash
    find_inode failed for name=logo-fb
    load: Failed to find inode
    can't find logo in flash
      1: Console on null
      2: Console on ttyS0
      3: Console on framebuffer
    Select option (1-3), other keys to stop autoboot:  0 
    ............................................................... done
    Un-Protected 63 sectors
    ### FS (squashfs) loading 'vmlinuz' to 0x200000
    ### FS load complete: 671057 bytes loaded to 0x200000
    ## Booting kernel from Legacy Image at 00200000 ...
       Image Name:   Linux-
       Image Type:   PowerPC Linux Kernel Image (gzip compressed)
       Data Size:    670993 Bytes = 655.3 kB
       Load Address: 00000000
       Entry Point:  00000000
       Verifying Checksum ... OK
       Uncompressing Kernel Image ... OK
    Linux version (arabeman@MyGentoo) (gcc version 3.4.6) #1 jeu. mai 27 07:49:15 CEST 2010
    On node 0 totalpages: 8192
    zone(0): 8192 pages.
    zone(1): 0 pages.
    zone(2): 0 pages.
    Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 dbox_duplex=
    Decrementer Frequency = 252000000/60
    m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
    m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
    Console: colour dummy device 80x25
    Calibrating delay loop... 66.96 BogoMIPS
    Memory: 30824k available (1144k kernel code, 340k data, 60k init, 0k highmem)
    Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
    Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
    Mount cache hash table entries: 512 (order: 0, 4096 bytes)
    Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
    Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
    POSIX conformance testing by UNIFIX
    Linux NET4.0 for Linux 2.4
    Based upon Swansea University Computer Society NET3.039
    Initializing RT netlink socket
    Starting kswapd
    devfs: v1.12c (20020818) Richard Gooch (
    devfs: boot_options: 0x1
    JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
    squashfs: version 3.0 (2006/03/15) Phillip Lougher
    i2c-core.o: i2c core module version 2.6.1 (20010830)
    i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
    CPM UART driver version 0.04
    ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
    pty: 256 Unix98 ptys configured
    half-duplex mode enabled
    eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:41:1f:8d
    loop: loaded (max 8 devices)
    D-Box 2 flash driver (size->0x800000 mem->0x10000000)
    D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
     Intel/Sharp Extended Query Table at 0x0035
    cfi_cmdset_0001: Erase suspend on write enabled
    Creating 6 MTD partitions on "D-Box 2 flash memory":
    0x00000000-0x00020000 : "BR bootloader"
    0x00020000-0x00040000 : "FLFS (U-Boot)"
    0x00040000-0x006a0000 : "root (squashfs+lzma)"
    0x006a0000-0x00800000 : "var (jffs2)"
    0x00020000-0x00800000 : "Flash without bootloader"
    0x00000000-0x00800000 : "Complete Flash"
    Linux video capture interface: v1.00
    mice: PS/2 mouse device common for all mice
    NET4: Linux TCP/IP 1.0 for NET4.0
    IP Protocols: ICMP, UDP, TCP
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP: Hash tables configured (established 2048 bind 4096)
    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    VFS: Mounted root (squashfs filesystem) readonly.
    Mounted devfs on /dev
    Freeing unused kernel memory: 60k init
    init started: BusyBox v1.14.4 (2010-05-27 08:56:52 CEST)
    starting pid 8, tty '': '/etc/init.d/sysinit'
    [BOOT] running /etc/init.d/sysinit
    Thu Jan  1 01:00:00 UTC 1970
    starting pid 22, tty '': '/etc/init.d/rcS'
    Please press Enter to activate this console. starting /etc/init.d/S05drivers ...
    [BOOT] running /etc/init.d/S05drivers
    tuxbox: no IDE-Interface detected
    Detected STB:
    	Vendor: Nokia
    	Model: D-BOX2  (2 flash chips)
    event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
    [i2c-8xx]: mpc 8xx i2c init
    [i2c-8xx]: adapter: 0
    lcd.o: init lcd driver module
    lcd.o: found KS0713/SED153X lcd interface
    $Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
    $Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
    DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
    DVB: VES1820(0): pwm=0x48
    DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
    dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
    $Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
    avia_av: $Id: avia_av_core.c,v 1.102 2010/05/25 19:58:20 dbt Exp $
    avia_av_core: Starting avia_av_wdt thread.
    avia_av: AVIA 500 LB4 found, sptsfix is off
    avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
    avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
    avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
    avia_gt_core: autodetecting chip type... GTX
    avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
    avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
    avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
    avia_gt_core: masking unhandled irq reg 1 bit 11
    avia_gt_core: masking unhandled irq reg 1 bit 13
    avia_gt_ucode: loaded ucode v0014
    avia_gt_ucode: ucode section filters enabled.
    avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
    avia_gt_core: masking unhandled irq reg 0 bit 6
    avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
    avia_gt_gv: set_input_size (width=720, height=576)
    avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
    avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
    avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
    avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
    avia_gt_core: Loaded AViA eNX/GTX driver
    avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
    avia_gt_gv: set_input_mode (mode=2)
    avia_gt_gv: set_input_size (width=720, height=576)
    avia_gt_gv: set_input_mode (mode=2)
    avia_gt_gv: set_input_size (width=720, height=576)
    avia_gt_gv: set_input_mode (mode=2)
    avia_gt_gv: set_input_size (width=720, height=576)
    Console: switching to colour frame buffer device 82x32
    avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
    avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
    avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
    avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
    avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
    avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
    avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
    starting /etc/init.d/S10network ...
    starting /etc/init.d/S10rtc ...
    starting /etc/init.d/S15syslogd ...
    Jan  1 02:00:10 dbox syslogd started: BusyBox v1.14.4
    starting /etc/init.d/S18rdate ...
    starting /etc/init.d/S20inetd ...
    starting /etc/init.d/S25cdkVcInfo ...
    starting /etc/init.d/S30autofs ...
    [BOOT] Starting the automounter
    starting /etc/init.d/S40tuxmaild ...
    starting /etc/init.d/S99gui ...
    Jan  1 02:00:14 dbox daemon.err automount[160]: failed to load map/bin/enigma: /lib/ no version information available (required by /bin/enigma)
    enigma, Copyright (C) dbox-Project
    enigma comes with ABSOLUTELY NO WARRANTY
    and also this:
    [eZapMain]wasSleeping is 0, wasDeepStandby is 0
    skin has undefined element: snr_progress
    skin has undefined element: agc_progress
    skin has undefined element: ber_progress
    skin has undefined element: snr_num
    skin has undefined element: agc_num
    skin has undefined element: ber_num
    skin has undefined element: snr_text
    skin has undefined element: agc_text
    skin has undefined element: ber_text
    skin has undefined element: fulltime
    skin has undefined element: date
    skin has undefined element: Picon
    skin has undefined element: pro_name
    skin has undefined element: videoformat
    skin has undefined element: frequency
    skin has undefined element: symbolryate
    skin has undefined element: polarisation
    skin has undefined element: fec
    skin has undefined element: bandwidth
    skin has undefined element: transmissionmode
    skin has undefined element: coderate_lp
    skin has undefined element: coderate_hp
    skin has undefined element: AudioOrPause
    skin has undefined element: vt
    skin has undefined element: vt_off
    skin has undefined element: audio_on
    skin has undefined element: audio_off
    skin has undefined element: sep_icon
    no sapi

    and this critical one:
    pluginname is tuxcom 1
    loading /lib/tuxbox/plugins/
    would exec (NORMAL) plugin /lib/tuxbox/plugins/
    start plugin thread...
    plugin thread running.. execute plugin now
    Tuxbox Commander Version 1.16TuxCom <Font "/share/fonts/pakenham.ttf" loaded>
    tuxcom: reading settings 
    tuxcom: could not open /var/tuxbox/config/tuxcom.conf !!!
    TuxCom init successful
    [EPGC] start cleanloop
    [EPGC] stop cleanloop
    [EPGC] 0 bytes for cache used
    execute plugin finished
    thread has completed..
    avia_gt_gv: set_input_mode (mode=2)
    avia_gt_gv: set_input_size (width=720, height=576)
    thread joined 0
    someone has stolen the focus
    icon is higher
    starting pid 223, tty '': '/etc/init.d/rcK'
    stoping /etc/init.d/K99gui ...
    stoping /etc/init.d/K40tuxmaild ...
    stoping /etc/init.d/K30autofs ...
    Stopping the automounter
    /etc/init.d/K30autofs: line 69: can't open /var/run/ no such file
    kill: you need to specify whom to kill
    stoping /etc/init.d/K25cdkVcInfo ...
    stoping /etc/init.d/K20inetd ...
    stoping /etc/init.d/K18rdate ...
    stoping /etc/init.d/K15syslogd ...
    stoping /etc/init.d/K10rtc ...
    stoping /etc/init.d/K10network ...
    stoping /etc/init.d/K05drivers ...
    CXA2092 found
    The system is going down NOW!
    Sent SIGTERM to all processes
    Sent SIGKILL to all processes

    thank you

  3. #3
    VIP Member arabeman14's Avatar
    Join Date
    in front of my PC

    Re: looking for linux (tuxbox) developpers

    this enigma1 image for dbox2 (not dreambox!) should be better...
    gbox is supported ...


Similar Threads

  1. Replies: 0
    Last Post: 27-11-2009, 02:45:17
  2. New to Linux
    By almasan in forum AZBox
    Replies: 0
    Last Post: 25-06-2009, 20:52:17
  3. Linux 24/7/366
    By modifarid in forum CCcam Exchange: Local
    Replies: 0
    Last Post: 14-02-2009, 22:29:13
  4. New MCWST : a tool for Worldsat developpers
    By barbichou in forum Worldsat Information and Tutorials
    Replies: 6
    Last Post: 30-11-2008, 09:39:26
  5. What linux box??? :s
    By jamessmart747 in forum General Discussions: Satellite Receivers
    Replies: 0
    Last Post: 20-01-2008, 23:15:55

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts