Results 1 to 5 of 5

Thread: Help to program a original dragonlaod card based on PIC "F84"

  1. #1
    Junior Member
    Join Date
    07-04-2005
    Posts
    17
    Uploads
    0

    Unhappy Help to program a original dragonlaod card based on PIC "F84"

    • Which are the steps for to program a dragonlaod card, based on PIC
    "F84" is printed on the card ,I work with Windows 2000 and Infinity USB Unlimited V2.50 or new software v2.60,echostar 2600 ip
    • I have been to the dragon site and downloaded pred. 3.12 I have opened the file and have the following ,predator312.bin, Fun7ldr.hex, predator312.dra, predator.IDs,"how to and read me" could you explain which file goes where, for dragonlaod card based on PIC "F84"
    • Should I downloaded all firmware or just the last one
    Thank you in advance has all the team for help

  2. #2
    Junior Member
    Join Date
    30-03-2005
    Posts
    22
    Uploads
    0

    Re: Help to program a original dragonlaod card based on PIC "F84"

    first step: You have to write in dragon load cadr f84a LOAD2MB.hex
    to lad this hex file in your card - be shure that you were selected single pic f84a without external flash.
    after that second step: tourn your program module in phoenix module 6MHz clock, and it have to bee conected via com (rs232)
    open the Loader.exe program and it the presense of your loader in module - then try to select *.dra file - and that is it.

  3. #3
    Junior Member
    Join Date
    29-09-2005
    Posts
    13
    Uploads
    0

    Re: Help to program a original dragonlaod card based on PIC "F84"

    have been using infinity for a while now and the best advise i can give is to always use the latest software.
    dont read the card ,just pick the f64c dragon loader card.
    i see you have found the file ,you just need the dra.file nothing else.
    put this file into eeprom 1 and split so it fills eeprom 2.
    write and hey presto.it take a couple of minutes.
    cheeseyy

  4. #4
    New Member
    Join Date
    04-04-2005
    Posts
    5
    Uploads
    0

    Re: Help to program a original dragonlaod card based on PIC "F84"

    @ LEE
    Please, tell me with what Programmer (I have Multiprog2001) and HOW I can program my Loader Card F84A using LOAD2MB.hex.
    What Soft alows me to load LOAD2MB.hex and than to prog.
    Thanx a lot in advance
    orog

  5. #5
    Junior Member
    Join Date
    30-03-2005
    Posts
    22
    Uploads
    0

    Re: Help to program a original dragonlaod card based on PIC "F84"

    Hi @orog, sorry for later, I haven't been there too much time.

    First step - I had used the simple JDM Pic programer (wich I made by myselv)with JGPROG_18_04_2003_VIP_Funrrari or icprog105C_XP
    with JDM you can write in single pic mode the LOAD2MB.hex
    (single pic mode - Just load pic flash, without any external eeproms).
    Then in Phoenix programer (mode phoenix 6MHz) with dragonload.exe select the last *.dra, and write it in external eeprom.

Similar Threads

  1. Info M.O.S.C "Modified Original Smart Card"
    By posedon in forum Albanian / Shqip
    Replies: 0
    Last Post: 05-01-2010, 15:11:30
  2. Replies: 0
    Last Post: 16-10-2009, 21:09:55
  3. Replies: 0
    Last Post: 10-09-2009, 20:23:41
  4. Tutorial Please poste here all solutions card sharing ALI "B" et ALI "C"
    By radium in forum FTEmaximal Information and Tutorials
    Replies: 18
    Last Post: 03-05-2009, 13:43:56
  5. Yankse "original plugin by Vlinders" for DVB-s cards
    By hoangngan in forum DVB Plugins
    Replies: 4
    Last Post: 12-06-2006, 13:54:27

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •