Results 1 to 10 of 10

Thread: need help with trex

  1. #1
    Junior Member
    Join Date
    14-08-2006
    Posts
    10
    Uploads
    0

    need help with trex

    Yesterday i bought an trex cam
    and i need help how to program it
    before this cam i had an matric revolution and that was easy to update


    i have this thing (http://www.digicams-uk.com/images/cas1.bmp)
    and the program cis7.4

  2. #2
    VIP Member
    Join Date
    14-06-2005
    Posts
    544
    Uploads
    2

    Re: need help with trex

    Did you get a Dragon\T-Rex Loader Card at the same time as your T-Rex CAM? If not you'll do well to get One!
    Whatever you options some you ~will~ need some kind of 'Loadercard' even if it's just a Dummycard w/a CAS3 Interface.
    So you can update your CAM either with a Dummycard w/CAS Interface 3, or you could Program a 'Loadercard' (e.g. Fun7 ~2Mb~), in the case of a 2Mb Fun7 Card you will have to run the Dragon Restore Program on the Card first to, convert it into a 'Loadercard', but that should do nicely.
    AFAIK: It must be a Fun7 ~2Mb~ Card Fun6 ~1Mb~ and smaller will not work!

  3. #3
    Junior Member
    Join Date
    14-08-2006
    Posts
    10
    Uploads
    0

    Re: need help with trex

    is fun 7 an loadercard?
    i have 1 fun7

    but i cant click on that icon by the program cis7.4
    i go to repair > there i see > Dragon > but cant click on it

  4. #4
    VIP Member
    Join Date
    14-06-2005
    Posts
    544
    Uploads
    2

    Re: need help with trex

    Did you try re-formating (that ie eraseing), the Card first??

  5. #5
    Junior Member
    Join Date
    14-08-2006
    Posts
    10
    Uploads
    0

    Re: need help with trex

    first 1 thing
    i really apreciate that you help you

    can you pls explain how i can update in steps

    i start cis74
    i connect my cas to my pc
    and then...?

  6. #6
    VIP Member
    Join Date
    14-06-2005
    Posts
    544
    Uploads
    2

    Re: need help with trex

    Taken from the README: How to program a Fun7 2Mb Card
    ---------------------------------------------------------------

    Fun7 firmware update
    Interface phoenix not needed
    No need to erase card before (2 * 1024 external eeprom created, complete eeprom overwrite)

    Material Used:
    1-Programmer for Fun7 or PrussianCard5
    2-Dragon Fun7 loader

    Procedure for 2 external eeprom (BIN or HEX Format):
    1-Load Software programmer
    2-Select Fun7 or Prussiancard5
    3-Load Fun7FlashLoader.hex in flash
    4-Nothing in internal eeprom
    5-Load PredatorXXX_FUN7_EEPROM1 in EEprom Ext.1
    6-Load PredatorXXX_FUN7_EEPROM2 in EEprom Ext.2
    7-Burn card
    (XXX=predator version, ex 3.04)

    Procedure for 1 external eeprom:
    1-Load Software programmer
    2-Select Fun7 or Prussiancard5
    3-Load Fun7FlashLoader.hex in flash
    4-Nothing in internal eeprom
    5-Load PredatorXXX.Bin in EEprom Ext
    Clic on "(3)Reverse Span" when window appear
    6-Burn card
    (XXX=predator version, ex 3.04)


    (C)MASARE Team - Saoud007
    ---------------------------------------------------------------------

    I don't think I could have said it any better myself.

  7. #7
    Junior Member
    Join Date
    14-08-2006
    Posts
    10
    Uploads
    0

    Re: need help with trex

    thanks dude

    ill try if it works
    if i need help ill give you an pm or something

  8. #8
    Senior Member
    Join Date
    15-02-2006
    Posts
    134
    Uploads
    0

    Re: need help with trex

    If you only have a CAS2 interface you cannot do anything, you will need the add-on that will allow you to program the loadercard for the dragon or turn a Funcard 7 into a DragonLoader card.

    Otherwhise you need a CAS3 interface with the dummy card to program directly the Dragon/T-Rex CAM.

    PrČ

    Advice: please read the manual Duolabs

  9. #9
    Junior Member
    Join Date
    14-08-2006
    Posts
    10
    Uploads
    0

    Re: need help with trex

    a friend of me has cas3 i can borrow it from him
    but i dont know witch updates i need to install
    can sombody tell me that ?

    if i do the trex cam in the receiver i see firecrypt 1.3

  10. #10
    VIP Member
    Join Date
    14-06-2005
    Posts
    544
    Uploads
    2

    Re: need help with trex

    Do you have a Programer for Funcard / Cerebro / K3 etc...??
    CAS2 should be enough.
    Heck I have a Dynom!te Plus which is about the same thing as a CAS2 w/o the update abblilty to CAS3, and I hav had no problems yet.

    Yes with the CAS3 Interface and it's Dummycard you will be able to update the CAM!
    But, the rub is the CAS3 Interface is about the most expensive Programer you can buy!
    Using this just to program a Funcard now and again would be a waste!
    Ok I got that outa the way.

    You have to open some Program up that will work with your Programer Device.
    Beit a USB - Dynom!te Plus, Infinity or an older COM Port only Programer MasterCRD1 for ex.
    In the case if the Fun7 you should have Four Block to fill-in (normal Fun 2-6 only have 3 Blocks!).

    The Blocks on a fun 7 are:

    Flash: You should place the Fun7FlashLoader.hex -- here
    Int-EEPROM: Nothing goes in here!!
    Ext-EEPROM1: PredatorXXX_FUN7_EEP ROM1 in EEprom Ext.1
    Ext-EEPROM2: PredatorXXX_FUN7_EEP ROM1 in EEprom Ext.2

    XXX = Predator version (i.e. v3.46 w/working TPS)

    Now you can write to the Card, when it's done you'll have a working Loader Card. to Program your CI-Modual.

    BTW: Firecrypt 1.3 should be standard on every Dragon \ T-Rex sold.
    Given that the only Two Channels in Fire\Dreamcrypt are X-Plus and InXtc...

Similar Threads

  1. Trex Nagra 2
    By xmenek in forum Polish / Polski
    Replies: 2
    Last Post: 26-08-2009, 19:44:57
  2. Question TRex 4.6 vs Diablo
    By nsharma in forum Diablo Cam
    Replies: 4
    Last Post: 24-04-2008, 12:54:22
  3. TRex 4.6 vs Diablo
    By nsharma in forum Dragon Cam and T-Rex Cam
    Replies: 0
    Last Post: 31-03-2008, 18:06:51
  4. Trex super
    By matjason in forum Dragon Cam and T-Rex Cam
    Replies: 1
    Last Post: 30-11-2006, 17:52:23
  5. Trex problem
    By lctinferno in forum Dragon Cam and T-Rex Cam
    Replies: 2
    Last Post: 10-09-2006, 23:53:35

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •