Page 1 of 8 1236 ... LastLast
Results 1 to 10 of 78

Thread: Metabox Tools

  1. #1
    VIP Member -Amor-'s Avatar
    Join Date
    05-04-2005
    Posts
    278
    Uploads
    213

    Metabox Tools

    enjoy







    edited

  2. #2
    Member
    Join Date
    25-03-2005
    Location
    Bulgaria
    Posts
    40
    Uploads
    0

    New Code & Preset data sender2006

    Hi Metabox users,

    New Code & Preset data sender2006
    Thanks To Iredeto2engineer.


    E tb obrigado ao Cobra.

  3. #3

    eMETABOX III JTAG Problems

    OK, here's the story. I have an eMETABOX-III receiver, which I believe is a clone. It has a "MX 29LV160BTTC-70" flash chip.

    I downloaded a new bin called "download_for_usa.bin" and updated receiver with this bin via serial port. Killed my Metabox. Now when it is turned on it just had power light, but nothing on display. Pushing power button does nothing - still nothing on display.

    So I connect my JTAG and try and update with that. First thing I get is "Error reading from IRD (DCU Peek)" error. So according to instructions I found somewhere else, you have to run the WALL program, leave it running, then run JKEYS again. Now receiver says "ON" on display. Flash erases OK then programs OK.

    But receiver still doesn't work.

    What I am not 100% sure about:
    Latest bin file I am trying is called "eMetabox 3 Software Full ver.4.04.bin"
    I use WALL to load this to receiver. After bin has loaded I use JKEYS to reload this same bin file? Do I have to now load this same bin by serial port using Filesender program? I have tried this, it says No Answer. I have tried turning receiver off, then on right after I start Send. Attached is instruction file I found and have been using.

    Can someone help me out?
    Attached Files Attached Files

  4. #4
    New Member
    Join Date
    07-06-2005
    Posts
    3
    Uploads
    0

    Re: eMETABOX III JTAG Problems


  5. #5

    jtag_up

    other software for jtag your reciver easy and works good

    best regards
    cfl

  6. #6

    Metabox Tools

    loader

  7. #7

    MetaTools v1.0 by hslim

    hi @all...
    I found finally a handy Tool that I was searching for a long time.
    It can read/write keys directly from/to the BIN-file, allows to change the picture, calculates the crc checksum... it´s a Genuine Swiss Army Knife to modify metabox firmware (incl. importing keys from softcam.key files)

    Language: french & english

    enjoy ;)

  8. #8
    Junior Member
    Join Date
    01-03-2005
    Posts
    12
    Uploads
    0

    Re: Jtag metabox I detection oK but after error ???

    désolé, voici le fichier à injecter pour débloquer la mémoire intel 28f
    @+

  9. #9
    The Manager urmans's Avatar
    Join Date
    01-03-2005
    Posts
    1,596
    Uploads
    583

    Metabox Tools

    Loader metabox v1[1].5.1 (france)


  10. #10
    New Member
    Join Date
    23-07-2006
    Posts
    7
    Uploads
    68

    Re: SOS problème signal ASTON cobra Metabox CX avec lecteur carte

    I had the signal problem too,I dont understand french but if you had loaded wrong full soft and now you dont have signal(not green),load this soft first and after that dreamsoft or metadream.I hope this will help.

Page 1 of 8 1236 ... LastLast

Similar Threads

  1. Tutorial Metabox Tools
    By -Amor- in forum Manhattan Information and Tutorials
    Replies: 76
    Last Post: 20-06-2009, 17:10:01

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •