Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Em-tech 400irci

  1. #1

    Em-tech 400irci

    Czy ktos mi moze pomoc w ozywieniu tego tunka,potrzebuje dumpa z tego tunerka.

  2. #2
    Repreestor...
    Join Date
    19-03-2005
    Posts
    358
    Uploads
    160

    Re: Em-tech 400irci

    posejdon, a skad to wyrwales?
    pogrzebie, ale najpierw opisz "objawy"... Bo nigdy nie wiadomo....

    Pozdro
    Cr3pT
    FunFiles Team

  3. #3

    Re: Em-tech 400irci

    mieszkam w grecji i ogladam ich kanaly, ma wbudowane irdeto stad ten tunek.
    objawy,same 88:88 na wyswietlaczu i nic wiecej

  4. #4
    Repreestor...
    Join Date
    19-03-2005
    Posts
    358
    Uploads
    160

    Re: Em-tech 400irci

    I nic a nic na ladowanie czegokolwiek??
    bo dla mnie to soft uwalony....
    Zaraz poszukam czegos i uploadne..

  5. #5
    Repreestor...
    Join Date
    19-03-2005
    Posts
    358
    Uploads
    160

    Re: Em-tech 400irci

    OK - a oto software
    1) rozpakowac i zainstalowac
    2) dzialac
    3) jak potrzebna pomoc (z ladowaniem) napisac mi info tutaj w czym pomoc...

    proste?

    Firmware jest orginalne - nie zadne patchowane

    Best Regards
    Cr3pT
    FunFiles Team

  6. #6

    Re: Em-tech 400irci

    wszystko to mam ale RS232 nie dziala potrzebuje dumpa.
    w tym jest problem

  7. #7
    Repreestor...
    Join Date
    19-03-2005
    Posts
    358
    Uploads
    160

    Re: Em-tech 400irci

    OOO... sorrki - nie doczytalem - zaraz polookam - moze cos znajde
    Momencik...

    PS: a pytales na shoutbox'ie?

  8. #8
    Senior Member
    Join Date
    09-06-2005
    Posts
    104
    Uploads
    15

    Re: Em-tech 400irci

    Download Procedure for eMTech and Homecast receivers
    First of all, download "HCUpgrade.zip" and follow these steps-

    1. Copy the "HCUpgrade.zip" file - compressed by winzip program.
    (We Recommend make new directory: C:\HCUpgrade)

    2. Extract HCUpgrade.zip in the "HCUpgrade" directory on your PC.

    3. Press the "setup" file, then you can see the set up procedure.

    4. Follow the installation instructions.

    5. After setup is finished, you can find the HCUpgrade program in the program files.
    (press "Start" -->"program" -->"HCUpgrade")

    6. Download the software for the relevant model receiver from our site. This will be
    a binary file (.bin) or an .sgn file.

    7. Copy the upgraded new software file in proper directory.
    (We recommend to make new directory: C:\HCUpgrade\Software)

    8. Run HCUpgrade and select the Comms port you wish to use, either Com1 or Com2.

    9. Disconnect the receiver's AC power cord.

    10. Connect an RS 232 cable (Crossed type NULL MODEM CABLE- Pin No. 2 and 3) between PC and Receiver.
    (RS232 should be connected on the Com port youhave selected in HCUpgrade on the PC)

    11. After you start HCUpgrade, select 'Download' in the 'Mode' menu, and 'Prog Data' in the 'Tyoe' menu.
    Go to “BROWSE” and select the software for the receiver you wish to upgrade. The file can be .bin or .sgn.
    Select “DOWNLOAD” then press the start button.

    12. Connect your receiver to the mains and turn on the mains power.

    13. Wait unitl the download is complete, then you can use your receiver.
    ----------------------------------------------------------

  9. #9

    Re: Em-tech 400irci

    receiver is dead !!!!!! if you have ,please give me flash dump

  10. #10
    Senior Member
    Join Date
    09-06-2005
    Posts
    104
    Uploads
    15

    Re: Em-tech 400irci

    cannot help you sorry



    http://www.masterixweb-italy.com/new...oad_emtech.htm




    Best Regards


    PAN

Page 1 of 2 12 LastLast

Similar Threads

  1. Tutorial Guide for updating the clarke-tech/guia paso paso para actualizar el clarke-tech
    By CurroHD in forum Clarke-Tech / Xtrend Information and Tutorials
    Replies: 4
    Last Post: 02-06-2017, 19:00:31
  2. Tutorial Dr.HD F16>Clarke-Tech/Clarke-Tech>Dr.HD F16/Repair-Reparar Ctech
    By CurroHD in forum Clarke-Tech / Xtrend Information and Tutorials
    Replies: 24
    Last Post: 12-12-2015, 17:57:57
  3. c-tech
    By yannis in forum Clarke-Tech / Xtrend
    Replies: 0
    Last Post: 22-07-2009, 18:24:41
  4. Clarke-Tech Setting by GioppyGio® Update 01/12/2008 per Plus e normal Clarke-Tech 310
    By GioppyGio in forum Clarke-Tech / Xtrend Software and Tools
    Replies: 0
    Last Post: 01-12-2008, 13:51:47

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •