Results 1 to 2 of 2

Thread: Usb Smart Card Reader config... Help!

  1. #1

    Usb Smart Card Reader config... Help!

    Good night people.
    I have a server with Ubuntu server 14.04.5, where I have installed Oscam.
    I'm trying to set up Reader with a usb card reader, but I'm not able to configure it. Can anyone help me?
    I leave here the data of the reader ....
    Code:
    Bus 002 Device 002: ID 0bda:0165 Realtek Semiconductor Corp. 
    Device Descriptor:
      bLength                18
      bDescriptorType         1
      bcdUSB               2.00
      bDeviceClass            0 (Defined at Interface level)
      bDeviceSubClass         0 
      bDeviceProtocol         0 
      bMaxPacketSize0        64
      idVendor           0x0bda Realtek Semiconductor Corp.
      idProduct          0x0165 
      bcdDevice           61.23
      iManufacturer           1 Generic
      iProduct                6 Smart Card Reader Interface
      iSerial                 3 20070818000000000
      bNumConfigurations      1
      Configuration Descriptor:
        bLength                 9
        bDescriptorType         2
        wTotalLength           93
        bNumInterfaces          1
        bConfigurationValue     1
        iConfiguration          4 CARD READER
        bmAttributes         0xa0
          (Bus Powered)
          Remote Wakeup
        MaxPower              500mA
        Interface Descriptor:
          bLength                 9
          bDescriptorType         4
          bInterfaceNumber        0
          bAlternateSetting       0
          bNumEndpoints           3
          bInterfaceClass        11 Chip/SmartCard
          bInterfaceSubClass      0 
          bInterfaceProtocol      0 
          iInterface              6 Smart Card Reader Interface
          ChipCard Interface Descriptor:
            bLength                54
            bDescriptorType        33
            bcdCCID              1.10  (Warning: Only accurate for version 1.0)
            nMaxSlotIndex           0
            bVoltageSupport         7  5.0V 3.0V 1.8V 
            dwProtocols             3  T=0 T=1
            dwDefaultClock       3750
            dwMaxiumumClock      7500
            bNumClockSupported      0
            dwDataRate          10080 bps
            dwMaxDataRate      312500 bps
            bNumDataRatesSupp.      0
            dwMaxIFSD             254
            dwSyncProtocols  00000000 
            dwMechanical     00000000 
            dwFeatures       00010030
              Auto clock change
              Auto baud rate change
              TPDU level exchange
            dwMaxCCIDMsgLen       271
            bClassGetResponse      00
            bClassEnvelope         00
            wlcdLayout           none
            bPINSupport             0 
            bMaxCCIDBusySlots       1
          Endpoint Descriptor:
            bLength                 7
            bDescriptorType         5
            bEndpointAddress     0x83  EP 3 IN
            bmAttributes            3
              Transfer Type            Interrupt
              Synch Type               None
              Usage Type               Data
            wMaxPacketSize     0x0040  1x 64 bytes
            bInterval               8
          Endpoint Descriptor:
            bLength                 7
            bDescriptorType         5
            bEndpointAddress     0x05  EP 5 OUT
            bmAttributes            2
              Transfer Type            Bulk
              Synch Type               None
              Usage Type               Data
            wMaxPacketSize     0x0200  1x 512 bytes
            bInterval               0
          Endpoint Descriptor:
            bLength                 7
            bDescriptorType         5
            bEndpointAddress     0x86  EP 6 IN
            bmAttributes            2
              Transfer Type            Bulk
              Synch Type               None
              Usage Type               Data
            wMaxPacketSize     0x0200  1x 512 bytes
            bInterval               0
    Device Qualifier (for other device speed):
      bLength                10
      bDescriptorType         6
      bcdUSB               2.00
      bDeviceClass            0 (Defined at Interface level)
      bDeviceSubClass         0 
      bDeviceProtocol         0 
      bMaxPacketSize0        64
      bNumConfigurations      1
    Device Status:     0x0000
      (Bus Powered)

  2. #2
    Administrator laitram's Avatar
    Join Date
    12-03-2005
    Location
    .fr16
    Posts
    1,943
    Uploads
    31

    Re: Usb Smart Card Reader config... Help!

    Hi,

    You have to check

    1) install & set up your drivers
    2) create a reader
    3) Parametrating your reader (that allows oscam to read something, somewhere) a reader is like a file for CW, *.keys...
    4) Open your browser & connect to oscam... go to log to see what's append.

    You can get some help through your browser scanning oscam.

    What is your reader (name/type...)

    Mine is ARGO triple reader & work fine after a lot of tests.

    Have fun


Similar Threads

  1. Четец ACR38 (Smart Card Reader)
    By mminkov in forum Програматори
    Replies: 2
    Last Post: 21-01-2013, 15:35:19
  2. Polsat smart card reader
    By hasko in forum Карти
    Replies: 5
    Last Post: 26-08-2012, 21:39:59
  3. driverat per nje smart kart reader.
    By flor1 in forum Albanian / Shqip
    Replies: 3
    Last Post: 30-07-2009, 20:37:12
  4. Help Needed with USB smart card reader dvbs-pci
    By msujah27 in forum General Discussions: DVB-PCI Cards
    Replies: 0
    Last Post: 09-04-2009, 08:48:07
  5. Invalid smart card reader
    By BwtMagic in forum Clarke-Tech / Xtrend
    Replies: 0
    Last Post: 22-08-2008, 16:57:31

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •