Results 1 to 2 of 2

Thread: Dragon Twin Cam

  1. #1

    Dragon Twin Cam

    As dori o informatie..Se pot introduce manual key-le biss intr-un Dragon Twin Cam? Daca da, cum? Multumesc anticipat pentru eventualul ajutor..

  2. #2

    Re: Dragon Twin Cam

    How to program a Dragon CAM/Loader Card with Infinity USB Unlimited Programmer
    Programming Dragon 4.1 with Infinity USB Unlimited Programmer

    I couldn’t get the Infinity Unlimited Programmer to work with the usual Dragonloader.exe files. Therefore, I had to use the software provided with the programmer. Very easy to use when you know how.

    Check which card loader you have as the programming is different depending on your card. Cards will be printed with a label. If it says “F84A” it is a PIC card. If it says "FUN" then it is a FUN card. The loader file for the Fun7 is included in the Predator folder as FUN7LDR. The PIC loader, LOAD2MB, is not usually included in the Predator folder. A version can be found as part of the “Dragon CAM-Help-Files.zip.”.

    If you have the Fun7 card:

    * 1. Load FUN7LDR.hex into the flash area i.e. against the box labelled PIC
    * 2. Load the xxx.dra file into ext EEprom, select [2] Reverse Span when asked
    * 3. When done the window will look like this:
    * PIC: FUN7LDR.hex
    * Int. EEprom: Empty
    * Ext. EEprom: <Data from Ext. EEprom-file>
    * Ext. EEprom2: .dra
    * 4. Press “write” and sit back as the card is programmed
    * If you have the PIC16F84A card:
    * 1. Load LOAD2MB.hex into the flash area i.e. against the box labelled PIC
    * 2. Load xxx.dra file into ext EEprom, select [2] Reverse Span when asked
    * 3. When done the window will look like this:
    * PIC: LOAD2MB.hex
    * Ext. EEprom: <Data from Ext. EEprom-file>
    * Ext. EEprom2: .dra
    * 4. Press “write” and sit back as the card is programmed
    * When the programmer is finished it is then the normal method of loading the card into the Dragon CAM and the receiver.
    .................................................. .................................................. .................................................. .................
    Shi varianta cu Telecomanda,ca de fapt asta ai intrebat, :) :

    How to insert keys into a Dragon/T-Rex CAM
    How to insert keys to your Dragon/T-Rex CAM

    Here's a quicky on how to edit your New Matrix Reloaded Keys into a DRAGON CAM.

    * 1- Go into MENU in your receiver remote control.
    * 2- Go into CONDITIONAL ACCESS again with your remote control.
    * 3- Go into PREDATOR Vx.xx with your remote control.
    * 4- Go into DEBUG with your remote control.
    * 5- Go into NAGRAVISION for example or any other system.
    * 6- Go into for :- Digital+ 4101 ; TV Cabo 4901 ; Polsat 7101 or any other package.
    * 7- In each one of either DigiTV or TV Cabo or Polsat you will see a choice of 2 key lines to edit: 00 or 01
    * 8- In this example there has been a change in DigiTV line 01
    * 9- Choose key line 01 and then you will see 3 small question marks. There you enter the keys which are in digits (DEC). You can get the keys from our keys and files section.
    * 10- Once you have entered those 8 sets of 3 digits. The menu will save. them
    * 11- Change any other keys you like, and check the keys on screen against the ones you have wrote down.
    * 12- Exit out of all of the menus until you come back to your FTA channel.
    * 13- Switch ON your receiver and go into a scrambled signal.
    * You should now be able to watch DigiTV or whatever you have changed.



    Eu nu am dar am cautat ca sa pot sa-tzi dau un raspuns.
    Numai Bine Tuturor
    Doozer2008

Similar Threads

  1. T-Rex twin mod upgrade
    By Momba0 in forum General Discussions: Cams
    Replies: 3
    Last Post: 18-08-2011, 21:28:11
  2. New Echolink El 600 Twin usb pvr
    By karympatcha in forum Echolink Firmware
    Replies: 4
    Last Post: 26-05-2010, 00:32:30
  3. T-Rex Cam twin module rev 1.0
    By gizmo1957 in forum Dragon Cam and T-Rex Cam
    Replies: 0
    Last Post: 30-08-2009, 15:50:45
  4. Twin card reader (dragon cam)
    By srood123 in forum Dragon Cam and T-Rex Cam
    Replies: 2
    Last Post: 30-03-2006, 22:57:45
  5. T-rex Twin
    By pinky99 in forum Dragon Cam and T-Rex Cam
    Replies: 1
    Last Post: 22-02-2006, 12:18:26

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •