Dreambox and how to use it "for bigginers"

[dreams@t]

2. Directions for those who have a hub: (exp: 1pc 1 pc 1 dream)
Overview: RJ45 rights and connected the hub to each machine connected to the master PC and modem to the hub.
On the dreambox (remote control)
menu / setup / expert setup / communication setup
IP: 192.168.0. (5 eg) DHCP fired (hint: unchecked for dhcp: ok button, before wanting to change the ip or no access)
Netmask: 255.255.255.0
Type lan
Name Server: 192.168.0.1
Gateway: 192.168.0.1
Enable network checked
Green button (apply)
On your PC, Start / connection / add a network connection
and next next next
Restart your dreambox (remote control button on the top right, push the 3 seconds click on restart
Now is your dreambox ping,
Start / Run / cmd / ping / 192.168.0.5
Or a good little program too to see if everything is ok
DCC:
Open your program and click on the top left configuration and choose the top left switch / hub
Ip pc: click on reconnect: 102.168.0.1
IP dreambox steps: 192.168.0.5 click sought
Nothing was added to the hub, but you must now you see the green band that connects a PC and hub dream.

[dreams@t]

3.Indications for those who have a modem router:
Summary: RJ45 rights, connected the router to each machine!
We will assume that your router is configured, and it has the IP 192.168.1.1 (and of course it is connected with RJ45 right to your dreambox)
On the dreambox: (remote control)
Button / menu / setup / expert setup / communication setup.
IP: 192.168.1.5 (dhcp unchecked .. click ok on dhcp and unchecked power to change ip)
Netmask: 255.255.255.0
Type: Lan
Nameserveur: 192.168.1.1 (look router becomes nameserver)
Gateway: 192.168.1.1
Enable network: checked
Port: 80, and green button to save
On your PC, Start / connection / add a network connection
next next next and finish up .......
Reboot your dreambox now (button at top right, 3 seconds poursses above and restart.
Now we do a ping on dreambox,
Start / Run / cmd / ping / 192.168.1.5
Or you use DCC, to Make sure, that everything is ok;
DCC works program, and click on configuration (upper left of the window)
Below pc, you click on reconnect
Below the steps dreambox: 192.168.1.5 (looks and click)
Below the steps router: 192.168.1.1 click sought
At this point, you should see a green band on the window, which connects to my pc and the router dream,
You extinguish your dreambox
Now you can put your usb stick in your dreambox
You turn your dream
And you open
FLASHWIZARD_PRO 6.3
click on configuration (bottom left)
dreambox ip: 192.168.0.5
login: root
pass: dreambox
Now we will format the stick, still in that window click USB stick format from 1 (no further explanation to be given)
Now click on install or remove firmware in multiboot
It will ask you to install the multiboot you answer yes or ok
you should see a disk drive, one USB Stick
(With a green dot in front, if you see a yellow dot click on the icon)
in flash you should see it appear flashimage
You click on the yellow folder (right) and you'll find on your pc image GEMINI 2 that you download it, ask yourself if you want to install on your stick or on your SD, you chose to stick
you leave your new image installed .....
ok once you reboot your dreambox, and again, configure, as pointed out above
pal ....... (Do not forget to change the ip menu / setup / expertsetup / communication setup .....
Now, we're going to download emus and of course the keys
To disable the Windows firewall and the firewall like zone alarm
Blue button on the remote
Addons
Ok
Download and install
Ok
Cam
Ok
A list should appear if it is not c apara that Internet connections are not made
Select the cam newcamd 6.01beta with arrows up down
Click ok
It must download
whene you download a panel opens up and
Selects yes
A click is ok
You return a cam
You repeat the following for the cam
Newcamd 5.28 cardspider
Scam 2.5
CAMD 7.09
Radesgast 3.0 Final
done
You go cam_conf
Ok
A list appears
You select the cam_conf of cams that you have installed
Even manipulations for cams
Once done
Exit
Exit
Exit
done
You go cam_plug
Ok
A list appears
You select the cam_conf of cams that you have installed
Even manipulations for cams
Once done
Exit
Exit
Exit
done
You go on keys
Ok
A list appears
You select the keys of the cams that you have installed
Even manipulations for cams
done
Exit
Exit
Exit
Blue button
Ok
The list of webcam you have installed appears
You select newcamd 6.01 / beta
Ok
Green Button
You reboot your dream
Blue button
You must be on newcamd 6.01/beta
Exit
If you have a map or c + CSAT, put the card into slot at the top, bottom and chip down, be attention turne off dream
That's all!
emus in the Dl install manual has put in var / tmp