DM800 dead after flash "Solved"

[samnabil]

i flashed my dm800 to Nabilo BlackHole
evey thing went fine on the flash untill final power down and power up starts the display states,Dream Multimedia ->error?look at dm7000.com #ERR01: NO CA FOUND I try to use a null modem cable and try dream up to flash didn't work any help pls
many thanks
samnabil

[aandra]

Flash with 0-modem (null modem) cable! It helps, but flashing in this method take about 30 minutes ore more!

[laitram]

i flashed my dm800 to Nabilo BlackHole
evey thing went fine on the flash untill final power down and power up starts the display states,Dream Multimedia ->error?look at dm7000.com #ERR01: NO CA FOUND I try to use a null modem cable and try dream up to flash didn't work any help pls
many thanks
samnabil

Hi

CA = conditionnal access
Seems your dm800 want to find a CA...
I think you're flashing your dm800 with a backup.
This is a wrong way... use à special dm800 image as xxxxxx.nfi with deamUP & don't forget to unflat the file on a folder before using dreamUP.

G luck

[samnabil]

hi
thanks for reply, but I am new with the DM 800 system, and this is my first time using the dream box. I try to flush by using dream up but still not working ,log in appears in the screen (21:12:38 box type: DM800and ) then it shows connection prepared. swich on the dream box.When I unplug and plug in and swich the dream box nothing happen.Any solution?
many thanks

[laitram]

hi
thanks for reply, but I am new with the DM 800 system, and this is my first time using the dream box. I try to flush by using dream up but still not working ,log in appears in the screen (21:12:38 box type: DM800and )
then you've to choose flash button on dreamUP & give the way for image to flash. then it shows connection prepared. swich on the dream box.When I unplug and plug in and swich the dream box nothing happen.Any solution?
many thanks

1) unplug all wires except rs 232
2) start dreamUP on your PC & clic connect
3) plug POWER on
4) dreamUP must see your dm800 If OK then flash button is possible on dreamUP
5) Clic on flash & give to dreamUP the good way to the new image
6)Read the progress cursor & wait approx. 20 min
7) cursor full = flash OK disconnect power and reboot your dreambox.

[samnabil]

1) unplug all wires except rs 232
2) start dreamUP on your PC & clic connect
3) plug POWER on
4) dreamUP must see your dm800 If OK then flash button is possible on dreamUP
5) Clic on flash & give to dreamUP the good way to the new image
6)Read the progress cursor & wait approx. 20 min
7) cursor full = flash OK disconnect power and reboot your dreambox.

hi
i did what you told me but nothing happen!
cheers
sam

[laitram]

Hi

hi
thanks for reply, but I am new with the DM 800 system, and this is my first time using the dream box. I try to flush by using dream up but still not working ,log in appears in the screen (21:12:38 box type: DM800and ) then it shows connection prepared. swich on the dream box.When I unplug and plug in and swich the dream box nothing happen.Any solution?
many thanks

You don't need reset your dream...

Switch off the dreambox go to step 1 & read carefully for proceed.

log in appears in the screen (21:12:38 box type: DM800and ) at this time, dreamUp is connected to dream & wait you are selecting flash button & give the way before proceed to flash...

I really think your dream is OK do it again please

By the way! is your dream oled display indicate an IP adress ???

[alfred_1]

Is your DB 800 a Clone? If its a clone you have to flash an Image which is suitable to its Bootloader...try flashing with a an older Nabilo Image with a bootloader of ss69...perhaps a 0.7 Nabilo Image which has this bootloader

[laitram]

Is your DB 800 a Clone? If its a clone you have to flash an Image which is suitable to its Bootloader...try flashing with a an older Nabilo Image with a bootloader of ss69...perhaps a 0.7 Nabilo Image which has this bootloader

Hi

I approve this way... try again with old image

[samnabil]

Hi
Thanks for reply, i did DM UP log in appears in the screen (21:12:38 box type: DM800and ) at this time,i wait to selecting flash button nonthing goes in flash !!

Cheers

Sam