Hallo zusammen,
Ich lebe in Österreich und habe mir grade eine Dreambox DM 800 S gekauft. Nun möchte ich noch ein Sky Abo abschliessen (Schüssel auf Astra habe ich schon). Meine Frage: kann ich die Sky Karte problemlos mit der Dreambox nutzen ? Selbige scheint nämlich nicht auf der Liste zertifizierter Receiver für Sky auf
lg
Hi Kuban,
Ich bin zwar selbst kein Dreambox-Spezialist, aber prinzipiell funzt die sky-Karte schon mit der Dreambox. Du musst halt auf entsprechende Image und Software aufpassen. Weitere Informationen findest du in der Dreambox-Section.
LG
Andrushenka
Re:CCconfig
######################################## ##############################
# Other config settings #
######################################## ##############################
# server shall listen on this port pro incoming connections
# default port is 12000, disable server with parm -s or set port 0
#
#SERVER LISTEN PORT : 12000
# server can give some info about server and client connections
# and cardinfo using telnet or webbrowser.
#
# Switch on/off access to info
# default is yes
#
ALLOW TELNETINFO: no
ALLOW WEBINFO: yes
# Show extended client info when showing client list
# default is yes
#
#SHOW EXTENEDED CLIENT INFO : no
# The webinfo service can be protected with a username and password.
# This is switched off by default
#
WEBINFO USERNAME : leoleoman
WEBINFO PASSWORD : leoman
# The telnetinfo service can be protected with a username and password.
# This is switched off by default
#
#TELNETINFO USERNAME : <username>
#TELNETINFO PASSWORD : <password>
# default port for telnet is 16000
# default port for web is 16001
# supported commands:
# info
# activeclients
# clients
# servers
# shares
# providers
# entitlements
# example use:
# echo servers | telnet localhost 16000
# go with your browser to http://ip_CCcam_server:16001
#
#TELNETINFO LISTEN PORT : 16000
WEBINFO LISTEN PORT : 16001
# time in seconds to keep On Screen Display active.
# default is 0 (turned off)
#
#ZAP OSD TIME : 3
# username used to show popup (default : root)
#OSD USERNAME : root
# password used to show popup (default : dreambox)
#OSD PASSWORD : dreambox
# port used to show popup (default : 80)
#OSD PORT : 80
# Serial reader config. Add as many as you have attached too your system
# replaces old name 'PHOENIX READER PATH', but still works.
# default is none
# optionally add readertype : phoenix,mouse,uniprog,sc8in1,smartreader +
# (when non readertype given defaults to uniprog (e.g. for mastera))
#
# SERIAL READER : <device> <type>
#
# example
#
SERIAL READER : /dev/tts/0 mastercrd
# Serial reader smartcard write delay.
# Setting to finetune smartcard write speed, optimal setting depends on speed of system, and
# speed of card. Default value is calculated, but can overrule by setting.
# Use number of microseconds delay between bytes, 0 = no delay, -1 = calculated default
# Note: huge difference between values 0 and 1, because of schedular overhead
#
# SMARTCARD WRITE DELAY : <device> <delay>
#
# example, 10ms write delay on smartcard in reader attached to /dev/ttyUSB0
#
#SMARTCARD WRITE DELAY: /dev/ttyUSB0 10000
#
# NOTE on sc8in1; because 8 smartcards are used on the same devicename, use
# devicename_0 .. devicename_7 for settings which require devicename to make
# settings per smartcard. example /dev/ttyS0_0, /dev/ttyS0_1 ..
# example, 8ms write delay between bytes to smartcard on last sc8in1 channel, attached to /dev/tts/0
#
#SMARTCARD WRITE DELAY: /dev/tts/0_7 8000
# Smartcard clock speed override
# Setting override specified speed for smartcard.
# Don't add setting unless you're sure what you're doing.
# In 99% of the cases the reader selects the optimal speed.
# Adding this setting either slows your card down, or might destroy it.
#
# SMARTCARD CLOCK FREQUENCY : <device> <freq>
#
# example
#
SMARTCARD CLOCK FREQUENCY : /dev/tts/0 6000000
# if timing should be shown in OSD and debug output
# default is no (turned off)
#
#SHOW TIMING : yes
# enables mini OSD which shows server(type), cardreader, keys or fta only
# default is no (turned off)
#
MINI OSD : yes
# turns debugging on and off
# default is no (turned off)
#
#DEBUG : yes
# should CCcam try to read and parse newcamd.conf for server connections
# default is no (turned off)
#
#NEWCAMD CONF : yes
# configure what EMM blocker you want. Add as many as readers you have attached
# default is blocking nothing
#
# B: /dev/sci0 01
# 00 - nothing
# 01 - sa blocked
# 02 - ua blocked
# 04 - ga blocked
# and sum of for combinations
#
#examples
#
#B: /dev/tts/0 07
#B: /dev/sci0 01
# disable all local EMM readers
# saves lots of CPU, but you won't get any updates anymore
# (unless you get updates from your clients)
#
# default: no
#
#DISABLE EMM : yes
# with this setting you can
# allow a client on two hops away
# to send the updates to the cardserver
#
# default : no
#
#EXTRA EMM LEVEL : yes
# with this setting you can
# configure how many emm listeners are started.
# for example use 2 when recording
# and viewing different systems and both need constant updates
#
# default : 1
#
#EMM THREADS : 1
# overrule the nds boxkey (4 byte hex)
#
# BOXKEY: <device> <byte1> <byte2> <byte3> <byte4>
#
#example
#
BOXKEY: /dev/sci1 ----------oben
BOXKEY: /dev/sci0 ----------unten raute zeichen muß weg
Die Sky Card läuft ohne Probleme in der Dream mit cccam, oder scam, die S02, oder die V13.
Soviel ich weiss läuft das NICHT mit der Dream.Originally Posted by kiliantv
Dieses Verschlüsselungssystem ist nur mit einer Karte und den dazugehörigen Receiver mit BOXKEY gepaart!!!!
BASTA!
Was möchtest uns Du da mitteilen???
Hast Du Deinen Ordner der CCcam.cfg mal hier reinkopiert????
Es läuft mit der dreambox, auch CS geht.
Also die Sky German Card rennt Super mit cccam, und auch mit scam, alle Cards, ob die Nagra S02 oder die N*S V13 Card.
Posting Permissions
Reply With Quote