Hello,
You can found it here: http://www.satsupreme.com/showthread...436#post617436
I'm still getting some error msg on a debug mode:
this one is not critical:
Code:
verify sig: 262
Branching to 0x40000
U-Boot 2009.08 (Tuxbox) (mai 27 2010 - 07:47:45)
CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . done.
find_inode failed for name=boot.conf
load: Failed to find inode
FB: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
LCD: ready
find_inode failed for name=logo-lcd
load: Failed to find inode
ready - can't find logo in flash
find_inode failed for name=logo-fb
load: Failed to find inode
can't find logo in flash
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
............................................................... done
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x200000
### FS load complete: 671057 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
Image Name: Linux-2.4.37.9-dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 670993 Bytes = 655.3 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.37.9-dbox2 (arabeman@MyGentoo) (gcc version 3.4.6) #1 jeu. mai 27 07:49:15 CEST 2010
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 dbox_duplex=
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30824k available (1144k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch ([email protected])
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:41:1f:8d
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (squashfs+lzma)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.14.4 (2010-05-27 08:56:52 CEST)
starting pid 8, tty '': '/etc/init.d/sysinit'
[BOOT] running /etc/init.d/sysinit
Thu Jan 1 01:00:00 UTC 1970
starting pid 22, tty '': '/etc/init.d/rcS'
Please press Enter to activate this console. starting /etc/init.d/S05drivers ...
[BOOT] running /etc/init.d/S05drivers
tuxbox: no IDE-Interface detected
Detected STB:
Vendor: Nokia
Model: D-BOX2 (2 flash chips)
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.102 2010/05/25 19:58:20 dbt Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: AVIA 500 LB4 found, sptsfix is off
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters enabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
starting /etc/init.d/S10network ...
starting /etc/init.d/S10rtc ...
starting /etc/init.d/S15syslogd ...
Jan 1 02:00:10 dbox syslog.info syslogd started: BusyBox v1.14.4
starting /etc/init.d/S18rdate ...
starting /etc/init.d/S20inetd ...
starting /etc/init.d/S25cdkVcInfo ...
starting /etc/init.d/S30autofs ...
[BOOT] Starting the automounter
starting /etc/init.d/S40tuxmaild ...
starting /etc/init.d/S99gui ...
Jan 1 02:00:14 dbox daemon.err automount[160]: failed to load map/bin/enigma: /lib/libpng14.so.14: no version information available (required by /bin/enigma)
enigma, Copyright (C) dbox-Project
enigma comes with ABSOLUTELY NO WARRANTY
and also this:
Code:
[eZapMain]wasSleeping is 0, wasDeepStandby is 0
skin has undefined element: snr_progress
skin has undefined element: agc_progress
skin has undefined element: ber_progress
skin has undefined element: snr_num
skin has undefined element: agc_num
skin has undefined element: ber_num
skin has undefined element: snr_text
skin has undefined element: agc_text
skin has undefined element: ber_text
skin has undefined element: fulltime
skin has undefined element: date
skin has undefined element: Picon
skin has undefined element: pro_name
skin has undefined element: videoformat
skin has undefined element: frequency
skin has undefined element: symbolryate
skin has undefined element: polarisation
skin has undefined element: fec
skin has undefined element: bandwidth
skin has undefined element: transmissionmode
skin has undefined element: coderate_lp
skin has undefined element: coderate_hp
skin has undefined element: AudioOrPause
skin has undefined element: vt
skin has undefined element: vt_off
skin has undefined element: audio_on
skin has undefined element: audio_off
skin has undefined element: sep_icon
no sapi
and this critical one:
Code:
pluginname is tuxcom 1
loading /lib/tuxbox/plugins/tuxcom.so
would exec (NORMAL) plugin /lib/tuxbox/plugins/tuxcom.so
start plugin thread...
plugin thread running.. execute plugin now
Tuxbox Commander Version 1.16TuxCom <Font "/share/fonts/pakenham.ttf" loaded>
tuxcom: reading settings
tuxcom: could not open /var/tuxbox/config/tuxcom.conf !!!
TuxCom init successful
[EPGC] start cleanloop
[EPGC] stop cleanloop
[EPGC] 0 bytes for cache used
execute plugin finished
thread has completed..
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
thread joined 0
someone has stolen the focus
icon is higher
Shutdown
starting pid 223, tty '': '/etc/init.d/rcK'
stoping /etc/init.d/K99gui ...
stoping /etc/init.d/K40tuxmaild ...
stoping /etc/init.d/K30autofs ...
Stopping the automounter
/etc/init.d/K30autofs: line 69: can't open /var/run/automount.pid: no such file
kill: you need to specify whom to kill
stoping /etc/init.d/K25cdkVcInfo ...
stoping /etc/init.d/K20inetd ...
stoping /etc/init.d/K18rdate ...
stoping /etc/init.d/K15syslogd ...
stoping /etc/init.d/K10rtc ...
stoping /etc/init.d/K10network ...
stoping /etc/init.d/K05drivers ...
CXA2092 found
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
:'(
thank you