Ndihme dreambox 800hd

[arjani10]

Pershendetje!Sapo kam blere nje dekoder dreambox 800hd dhe do te doja te dija se kur dua te ngarkoj setting me del error


Connected.
Dreambox response: Login successful.
** Retrieving file list of "/var/tuxbox/config/enigma/" **
Starting FTP transfer
Transfer complete
** Retrieving file list of "/var/tuxbox/config/enigma/" **
Starting FTP transfer
Transfer complete
Neither a "services" nor a "lamedb" file was found in directory "%" on the Dreambox. /var/tuxbox/config/enigma/
Check the dream path settings on the option panel to point to the correct Dreambox directories and try again.
Disconnecting.
Disconnected.
Sending Reload commands.
This might take up to a few minutes to let the Dreambox complete the reloading.
Network response: HTTP/1.1 404 Not Found
Could not connect to Dreambox on IP adress xx.xxx.xxx, check the IP address and/or your network.
Connecting to xx.xxx.xx.
Connected.
Dreambox response: Login successful.
** Retrieving file list of "/var/tuxbox/config/enigma/" **
Starting FTP transfer
Transfer complete
** Retrieving file list of "/var/tuxbox/config/enigma/" **
Starting FTP transfer
Transfer complete
Neither a "services" nor a "lamedb" file was found in directory "%" on the Dreambox. /var/tuxbox/config/enigma/
Check the dream path settings on the option panel to point to the correct Dreambox directories and try again.
Disconnecting.
Disconnected.
Sending Reload commands.
This might take up to a few minutes to let the Dreambox complete the reloading.
Network response: HTTP/1.1 404 Not Found
Could not connect to Dreambox on IP adress xx.xxx.xxx.xx. check the IP address and/or your network.
Connecting to xx.xxx.xxx.xx.
Connected.
Dreambox response: Login successful.
** Retrieving file list of "/var/tuxbox/config/enigma/" **
Starting FTP transfer
Transfer complete
** Retrieving file list of "/var/tuxbox/config/enigma/" **
Starting FTP transfer
Transfer complete
Neither a "services" nor a "lamedb" file was found in directory "%" on the Dreambox. /var/tuxbox/config/enigma/
Check the dream path settings on the option panel to point to the correct Dreambox directories and try again.
Disconnecting.
Disconnected.



cfare duhet te bej qe te mund te hedh keto setting ne te???Falemnderit.

[Fiku75]

provo njehere ti hedhesh manualisht,

te duhet nje software dreamboxedit
dhe settings te fundit meri ketu mos harro te zgjedhesh enigma2

[arjani10]

Faleminderit per pergjigjen po me dreamboxedit me jep kete error qe kam shkruar me siper ,sme njef as usals per motorrr..

[best ven]

N.q.se ke image Nabilosat ja hedh direkt nga aparati

[arjani10]

Po me cmend ky 800hd isha mire me 500s.Ja arita me i vene kanalet duke perdorur vetem programin dreamset 229 i vetmi qe i bente ,ne te ka enigma 0404 po kanalet i shof si emer edhe pse dekoderi eshte i pozicionuar ne gradet e duhura dhe vene parametrat e motorit sic duhet nuk me jep nuk ka figure nuk e leviz as motorrin mos ka ndonje plugin qe even ne funksionim??

[best ven]

Kam pershtypjen se e ke problemin tek konfigurimi shiko njehere diseqc duhet ta vendosesh 1.2 per motor

[trimi606]

Po me cmend ky 800hd isha mire me 500s.Ja arita me i vene kanalet duke perdorur vetem programin dreamset 229 i vetmi qe i bente ,ne te ka enigma 0404 po kanalet i shof si emer edhe pse dekoderi eshte i pozicionuar ne gradet e duhura dhe vene parametrat e motorit sic duhet nuk me jep nuk ka figure nuk e leviz as motorrin mos ka ndonje plugin qe even ne funksionim??

nuk pe kuptoj aq mire problemin mirpo nese ke problem me konfigurimin e motorrit shiko ketu se si behet

Menu
Setup
Service Searching
Tuner Configurtion
pasi te hyni ne Configuration Mode e beni: advanced
Satellite: 01=19.2E ASTRA
Use usals for this sat: no
Stored position: 001 (dmth, si eshte nalt ne fillim te satelitit 01 ashtu duhet edhe ne Stored position)
LNB: LNB1
DiSEqC mode: 1.2
ato me posht nuk beni kurfar ndryshimi.
keshtu duhet ti beni ne secilin satelit qe deshironi ta keni ne motor.

pasi ta keni kryer dilni nga konfigurimi dhe shkoni ne:
Positioner setup
Tune: e shtyp tastin e Kuq dhe e zgjedh satelitin ku ne fillim e ka edhe numrin e pozites dhe shtyp OK
Positioner movement: me tastin e Gjelbert ose Verdhe e gjen ate satelit te cilin e ke zgjedh.
pasi ta gjen satelitin shkon ne:
Positioner storage, e regullon numrin e pozites si e ka ai satelit e shtyp tastin e gjelbert (Store position) dhe pastaj e shtyp tastin e verdhe (Goto position)

me te gjitha satelitet veprohet keshtu njejte vetem se numri i pozicioneve ndryshon.

[kekekeke]

shiko konfigurimin e AV