Version 2.1 (06.07.2010)
Code:Release r2: the reading of HDD temperature can be disabled(some watch from the HDD to Sleeping) Thx Jörg
Version 2.1 (06.07.2010)
Code:Release r2: the reading of HDD temperature can be disabled(some watch from the HDD to Sleeping) Thx Jörg
Release r3: HDD Temperatur auslesen ohne spinup (ich hoffe)
Release r3: HDD Temperature reading without spinup (I hope)
FanControl2 - Lüftersteuerung [09.07.2010]
THX JörgRelease r4: Sprache Niederländisch hinzugefügt (Danke Bschaar)
Release r4: added Dutch language (Thanks Bschaar)
Release r4
Code:- added Dutch language (Thanks Bschaar).
Release r6: HDD temperature is sometimes not read
Version 2.2 (13/08/2010)
- WebIF Enlargement - Logging
- Multi language support WebIF
- Monitor the extension menu (blue button)
- Monitor supplemented with speed
- Info button on the monitor enforces a unique reading of HDD temperature
- HDD-setting temperature reading in sleep mode (Idle mode is temperature ever read)
Car: At the start of FC2 will be tested once, if the HDD has started, if so, is the reading in sleep mode disabled
- Box shut down on reaching the set temperature or fan failure
Greetings Jörg
Code:=========================================================== FanControl2 by joergm6 Help V.2.2 Support forum: IHAD Acknowledgments: diddsen, _marv_ Spaeleus(it), mimi74(fr), Bschaar(nl) =========================================================== Apologies if the english translation is not always correct. Function -------- Control a 3pin or 4pin fan (PWM) depends from the average of the 2 highest temperature values. Slowly regulation, because temperatures are not too change quickly and there should no unnecessary CPU load. Security Features ----------------- If 30min no reports of the fan speed, it is assumed that the fan is defective. Regularly appears on the TV then an appropriate message. If standby mode the fan is off, the fan switched on, when the maximum temperature is exceed. The temperature drops by more than 3C the fan turns off again. The fan runs in the first 10 minutes with minimum speed. The overheat protection can be increased by up to 9C. It can be set when shutting down the box, at which temperature and fan failure. Preferences ----------- Fan off in Standby yes = Fan will be turned off if the box is in standby yes, Except for recording or HDD= Fan is turned off in standby if there is no recording and HDD is in Sleep-Mode Min speed At Temperature "static-temperature" and below it is set this speed. Max speed At Temperature "end-temperature" it is set this speed. Static temperature Until this temperature is not regulated, min speed is set. End Temperature This is the maximum temperature may occur, is this achieved, we will set the max speed. Initially, voltage and PWM When changing the values the fan is immediately set with these values. It can now be directly read off the speed. The controlling is nevertheless once again active. So quick look or change the values. These values are set when the box boots up or if the fan was switched off in standby. for 3pin Fan type For regulation of voltage 3-pin fan with tachometer signal. Is controlled only the voltage. Settings for PWM have no control. Sets the initial voltage to a value of Rotation rate, with the fan at the start of the Box initially intended to run. From this starting speed is regulated. for 4pin Fan type For regulation PWM, 4-pin Fan. First is controlled the PWM value. If the control range is no longer sufficient, if possible, also regulate the voltage. The voltage adjustment is required. Set the voltage on the Maximum value (for DM500HD set 5). But also a lower voltage level is useful. A lower voltage means a lower maximum speed and a lower minimum speed. Set the voltage as possible so that the control range with PWM enough. There are also fans spin at PWM = 0 to be too high. Reduce the voltage here, until the desired min Speed (including 0 is possible) is achieved. Have also the max speed in mind. PWM provides a value that corresponds to the speed, initially run the fan at the start of the Box. From this speed is regulated. for Fan type Control disabled The regulation is disabled. The fan runs with the last parameters further. The fan is not turned off! Check ----- This attempts to determine the minimum speed of the fan for the startup and the minimum before the fan speed goes shutdown. Similarly, the maximum speed for these settings is determined. (OK) mean value matches the settings (!!) values do not match. These details are for information and do not affect the regulation, within the possible. 4Pin to be displayed in addition information on the wider control range. That means it is on the PWM area also changed the voltage. Temperature Monitor ------------------- With the "info key", can the individual values of the temperatures are shown. Press the Info button for single reading of HDD temperature. Special Setup ------------- With the "Menu key" special values can be defined. Action in case of fan failure [show info] Notification of defective fan, box shut down or do nothing. Box shutdown at temperature (C) [65] Upon reaching the specified temperature, the box switch off (DeepStandby). Thermal protection increase at (C) [0] If the fan is off in standby the fan switched on at maximum temperature. This maximum temperature can be increased by up to 9C read HDD-Temperature in HDD-Standby-Mode [auto] yes = read HDD temperature in HDD-Standby no = read HDD temperature only when HDD is active Auto = at the start of FC2 once tested whether the HDD starts, and if so reading is disabled never = Temperature is never read DMM fancontrol disabled [No] Appears in the skins with temperature, the DMM-FanControl is active and also switch the fan. It caused unwanted on/off operations. Recommendation: Disable DMM-FanControl WebIF number of log entries [40] How many events should be show in WebIF. 40-999 Logging directory Choose the "OK" the place to which directory the log files are written. Data is written only if least 10MByte are free. Enable Data Logging There will be written every minute a record in the file FC2data.csv. This can called directly in Excel. If this file does not exist and will Option enabled, a header is generated. about 4kBytes each hour Enable Event Logging There will be written all Events in the file FC2events.txt. about 30kByte each hour Web Interface ------------- Call: http://dreamboxip/fancontrol Displays information about current fan-values and the last Event logs. Per hour a value for temperature and Speed is appears. With "FC2 Log", the log files are downloaded and the logging can be set. Miscellaneous ------------- All important for the fan current readings appears as a value and bar graph. The bar display range is based on the individually set parameters. FanControl2 is prepared for different languages. Currently, English (default), German, Italian, French POT file is in ipkg if anyone other languages would make available. The settings are stored in the normal Enigma2 settings and are therefore included in the backup / restore. ===========================================================
Version 2.3 (10/09/2010)
- Attend online chart of the last 48 hours (Firefox often requires an extra Refresh (F5))
- Automatic deletion of old data-logging values (adjustable in Setup)
- Support for multiple HDDs for the control
- Other minor fixes and adjustments
A few observations:
Firefox has for the chart display on Caching-Problem/wartet not the creation. Therefore often is an extra Refresh (F5) is necessary.
Small tips for the chart: You can zoom with the mouse an area somewhat, a left-click on a line item showing the value.
It supports multiple HDDs for control, but as the temperature is only displayed the highest value of HDDs logged. Several HDDs have probably built a few.
And at the end I want a say thx to Bschaar extra for his tireless support.
fancontrol2_2.4-20110102-r2
works only with new drivers of 2010 from Gemini 4.6 or other OE1.5/1.6 Images
for DM500HD, DM8000HD, DM800se
What it does at the moment:
- Control a 3pin or 4pin fan (PWM) fans
- Setting: (configuration via plugin list)
Fan type 3pin / 4pin / off control of /
Fan off in standby + except during recording or HDD
minimum and maximum speed
Control-rest and the end-temperature
Initial voltage and PWM value
- Slow control with almost no CPU load
- Safety Function: Fan on at maximum temperature, fan failure detection and emergency
- Base temperature is the average of the two highest temperatures!
- Check min / max speed of the fan
- Display of current values as a number and bar + + HDD temperature monitor all sensors
- Web info page http://ip.der.dream.box/fancontrol (activity, values, online chart)
- Data-logging (FC2data.csv) and event logging (FC2events.txt) in file
- Prepare multi-language (welcome to the pot file ipkg other languages)
Small FAQ
- Resting temperature: up to this temperature is not regulated and the minimum speed is set
- End temperature: the maximum temperature that may occur is reached this will set the maximum speed
(There is no recommendation for the temp area, try some of what can be achieved for the results, anything between 40-50 ° C)
- Voltage / PWM
If this value changes are immediately set for the fan (for the reading of the initial speed). However, it is now the basis of these values equal to more regulated. With these values, the fan starts Boxstart.
4pin: set to full power (DM500HD/DM800se to 5-10) or reached at a value of at least the maximum desired speed, set the initial speed with PWM (PWM is controlled, if not sufficient, the voltage)
3pin: (to be regulated voltage only) set top speed with power
- Fan type 3pin or 4pin
If you can not just looking, what type of fan has built one that can easily be found out. This change just the start PWM controller. Changes thereby the speed, it is a 4pin fan.
- Settings
The configured settings are stored in the Enigma settings and are therefore included in the Backup / Restore
- The speed is the real speed, other tools show twice, that of false
- The box must have an adjustable fan hardware port and temperature sensor (s) (tested on DM500HD and DM8000HD)
- Online Chart
The data logging must be enabled to do so. When logging directory, a USB stick or CF card can be used. A time as logging into the flash or / tmp is possible. It should also be recorded because of the limited space only a little. A logging on / media / hdd does the hard drive run constantly, so not recommended.
Event logging is looking for problems to appropriate (not necessary for chart)
- HDD Temperature
If the hard drive from the sleep mode wake up (every 10min), please ask "the reading of HDD temperature" to No, or Never!
- Installation
IPK Package
with FTP (DCC) to / tmp copy
changer with a file manager in the Verzeichins / tmp and install package
or
Telnet:
cd / tmp
ipkg install *. ipk
- Remove
ipkg remove enigma2-plugin-extensions-fancontrol2
- Note: Restart after installation / update / remove Enigma
I try and collect the HDDs, which allow a temperature reading in sleep without spinup:
not possible
Seagate ST3500312CS, ST31000322CS
Samsung SP2004C, HD203WI, SP2504C, HD321KJ, HD503HI
possible
WD WD10EAVS, WD10EADS, WD15EADS, WD20EADS, WD Scorpio Blue
Samsung HD510LJ
Version 2.4 (14/11/2010)
- System status logging (BoxOne; HDDon; Record) / lines on the chart / icons WebIF
- Attend fix for oe1.5 Images
- DM500HD new driver speed range following the change in the standby
- And as always: more small changes
R1 release (17.11.) Better detection of false voltage reduction
R2 Release (02.01.) Updated French language
- System status logging (BoxOne; HDDon; Record) / lines on the chart / WebIF icons
- Attend fix for oe1.5 Images
- DM500HD new driver: speed range following the change in the standby
- And as always: more small changes
R1 release (17.11.) Better detection of false voltage reduction
R2 Release (02.01.) French language updated
Counter: Release r1 = 603 Downloads
missing for the HDD temperature display in oe1.5 images (such as GP4.6/4.7) the smartmontools. These can be downloaded from Dreambox-update.
e.g. http://www.dreamboxupdate.com/opendr...ental/smartmon
tools_5.33-r0_mipsel.ipk
or http://www.dreamboxupdate.com/opendr...ental/mipsel/s for OE1.6
martmontools_5.38-r0_mipsel.ipk
Greetings Jörg
FanControl2
Code:16.01.2011-v2.4.r6
Posting Permissions
Reply With Quote