Nabilo v8 Mod lonas v4 mbox 023.4.r - Sbox
as me and some buddies have asked for the issue of card and updating here I bring the same image but with mod canvas v4 Sbox configured to put ash veneer card down,
Remember that you must add Sbox s e r i a l sbox.conf card on file in HEX.
Flaswizard charged without problems but I'm recommending that you have dreamup the forum to load these images.
* New Bootlogo boot.
* Only 18% occupied at / var (recieninstalada, then with some other plugin I'm at 30%).
* New Default Skin modified for Mbox04 Rihana_NET (includes d1 and d2 on the screen).
* Picture enhancement completely, eliminating all that is in use.
* Emus Mbox04 installed (023.4.r) and Sbox (ready to put the card with the plate low and rular pa).
* Installed scripts: Borrafakes of the compi Borraoffs cthulhufhtagn + plugin.
* Added in / var / keys / ident.info and ignore.list updated date.
* The Emus ... were installed in the / (root)
* Routes of Emus changed and now are / bin / mbox and / bin / Sbox (mbox eye to configure the control center and remember this.)
* Cwshare preconfigured with line C just to add your Dlin to it (do not substitute your own, just add your Dlin and delete the ones you are, remember to leave the C line to read the card and add your provider)
* To run the standby recalls stamdby.sh scrpt amend and replace where it says your password dreambox for your dream or not work if you changed the password If nothing changes nothing changes.
* The image is optimized for virtual or local Mbox, you only have to meterle the channel list and enjoy it.
* Mbox Center Plugin to view stats, color, card, etc ... (Click yellow button to access this)
* Default is only Mbox so you'll have to go to the blue button and select the command mbox + Sbox for you to read your card
* The image is pre-configured to read a card Ash land if you want to read another changes the providers for yours on the line C and has also added what corresponds in the folder keys 50000.list modify the lines for which G match your providers.
* This image is a respected throughout the web interface so you do not remove anything from 100 per 100 Nabil.
* Restarted one at 4:20 am and 4:45 put one in standby (remember to put your password to the script) if you want to change this by accessing the nabcron.dat in / var / etc / and edit or control right from the blue button and blue button again.
* Fixed a few bugs that had previous versions of Nabil v8 this is much more stable than the v3 and has even so much nonsense.
* The script is added startscript.sh loq ue to boot every time you boot or reboots the dream that you start metais loq ue to within the same script, it currently only has introduced borrafakes borraoff and which by a sleep of 3600 seconds (one hour) begin to function in this way we prevent the dream start to hang anything else because they do not start at the same peace that emus, we have given an hour's gap between the start of the emus and the script not to be hung and let the mbox make your function hello and such things.
This image does not bring any more script and only borraoff borrafakes the moment from what I have seen no problems share.onl is happening a lot lately,
Remember to update and ignore.list ident.info by that of the specific thread for this in the forum
not if I'm missing something but if I remember but will put it on the fly ....
remember that the settings for the Mbox Control Center now is this:
The image is set up and configure ASH GREY CARD FOR LACK OF A SERIAL IN HEX ADD YOUR BUT IF BY SEA WHAT ARE YOUR OTHER CARD FOR EXAMPLE you can see here VIACCES THE SET OF EACH:Code:Nombre de archivo: mbox direccion ip: la tuya jeje Ruta Mbox: /bin Ruta Keys: /var/keys Ruta Temp: /tmp Ruta Mbox cfg: /var/keys/mbox.cfg
sbox.conf
port.listCode:[main] server_only=0 # 0=emu+newcamd server 1=only newcamd server log=0 # 1=no log 1=log to /tmp/sbox.log //ALWAYS USE 0// userspath=/var/bin/users.sbox # users list webinterface=0 # 1=web interface on 0=web interface off webport=8181 # web interface port [slot0] active=1 # 0=inactive 1=active sci=/dev/sci0 # lower ncdserver=0 # 0=newcamd server off 1=newcamd server on deskey=0102030405060708091011121314 # newcamd deskey port=50000 # newcamd port mhz=0 # Mhz for card in this reader, DON'T WORK ON PHOENIX INTERFACE. Example: mhz=357, mhz=368 # How to ADD RSA for TIGER/NCMED cards # If your card is a ROM TIGER547 Rev124 (for example) # [TIGER547] <- this is the rom version from your card # rsa=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx # ONLY THIS, for config bloquer, portlist, etc, look at the examples above! #Nagra2/3 Example [CCCCCCCC] # nagra2 hexserial (4 bytes) rsa= # rsa "n" from this card (like newcs) boxkey= # boxkey from this card emm=0 # 0=accept all 1=block emms 2=block emmu 4=block emmg portlist=0 # use portlist or no portlistpath=/var/****/port.list # path from port.list #Nagra tiger/ncmed Example [CCCCCCCC] # nagra hexserial (4 bytes) emm=2 # 0=accept all 1=block emms 2=block emmu 4=block emmg portlist=0 # use portlist or no portlistpath= # path from port.list #Seca Example [CCCCCCCC] # seca hexserial (4 bytes) ok_view=0 # if ok_view=1 sbox simulates the "ok view this season" on seca smartcards emm=7 # 0=accept all 1=block emms 2=block emmu 4=block emmg portlist=0 # use portlist or no portlistpath= # path from port.list #Viaccess Example [CCCCCCCC] # via hexserial (4 bytes) emm=7 # 0=accept all 1=block emms 2=block emmu 4=block emmg portlist=0 # use portlist or no portlistpath= # path from port.list aeskey= # aeskey used by nano d2 #Irdeto Example [CCCCCCCC] # irdeto hexserial (4 bytes) camkey=0000000000000000 # CamKEY camkeydata=00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 emm=7 # 0=accept all 1=block emms 2=block emmu 4=block emmg portlist=0 # use portlist or no portlistpath= # path from port.list #NDS Example [CCCCCCCC] # nds hexserial (4 bytes) emm=7 # 0=accept all 1=block emms 2=block emmu 4=block emmg portlist=0 # use portlist or no portlistpath= # path from port.list boxid= # if sbox can't get boxid from card, add here manually #Conax Example [CCCCCCCC] # conax hexserial (4 bytes) emm=7 # 0=accept all 1=block emms 2=block emmu 4=block emmg portlist=0 # use portlist or no portlistpath= # path from port.list #Example configuration newcamd client [NewCamd] #server0=dummy:dummy@localhost:15050/0102030405060708091011121314/0 #server1=dummy:dummy@localhost:15051/0102030405060708091011121314/2 #server2=dummy:dummy@localhost:15052/0102030405060708091011121314/7
users.sboxCode:SA: { 0001 } # Channel1 SA: { 0002 } # Channel2 SA: { 0003 } # Channel3 SA: { 0004 } # Channel4
Code:#Example configuration file for sbox cardclient server # [slot0] # slot to connect # user=lonas # user # pass=lonas # password # au=1 # au on/off # [slot1] # slot to connect # user=lonas # user # pass=lonas # password # au=0 # au on/off
Code:http://www.megaupload.com/?d=26PHUWEN
Reply With Quote