Bonjour,
On en est où avec le décodeur Power Sky 1500 actuellement ?
Sait ton encore décrypter quelque chose avec des clés AES ?
Quelle est la dernière version du flash ? Quel programme faut-il pour flasher ? Merci pour vos infos et sites éventuels où je pourrais me renseigner.
salut jojosat59, je ne peux pas répondre à ta question, mais je voudrais un peu d'aide pour mon 1900ci avec firm dvbxtreme; je ne sais pas comment débloquer les cléfs (manip télécommande) ni comment faire pour les soft autoload pour t*s... si tu peux m'aider?
j'ai le demo PS 8210cisk qui est sur 8888 apres un mauvais flashage, j'ai le cable pour faire le jtag mais rien ne bouge avec jkeys 2.9.
qq a une soluce? sa serait sympa.
Hello,
I'm a newbie to the satellite word and I hope you can help.
I've been reading several forums and websites to understand what I need to do but so far I failed so I hope I'll get some help.
So here's what I know:
1) I bought recently a PowerSky PS1500E with an upgraded firmware AF1700 (note, there's no "E"). I read somewhere that PS1500E and AF1700E (by Arion) are similar and use the same firmware.
2) I got myself a null cable to connect to the RS232 port.
3) I've found on multiple websites the following softwares:
- gasoline ver 1.03
- autoarioner (can't say which version)
- ariter 2N 2.0 (in polish - can't find it in english)
- Arioner (also can't tell the version)
Now, here's the problem: I don't think I can get my laptop and the STB to communicate.
I read the instructions of all the softwares and they're all pretty similar: turn off the STB (standby), connect to laptop, start software, digit some code on the remote.
Here's what happens with Gasoline 1.03 (with other software I have the same results).
a) I start Gasoline
b) go on port settings and change to com3 115200. If I leave it on Com1 I get "COM1 open error" message. I checked with "mode" on a dos shell and indeed com1 is in use (modem) and com3 is available. baudrate is set to 115200.
c) click the blue arrow (download from STB)
d) a window pops up numberict attempted connections
e) I dial the code 74623 ad "HEY" appears blionking on the STB (as expected) but gasoline keeps attempting the connection but it never happens.
After some time (30 seconds or so) the STB goes back to standby
I tried also to type the code before starting gasoline but no luck.
I also tried to use other codes (for other softwares) like 74620, 74621
No changes.
With autoarioner I start the software, com1 is set to "Scan" automatically but it is red (expected - com1 is busy). So I un-check com1 and select com3. Com3 starts blinking yellow/green alternating. (I checked also com2 and com4 but they stay grey).
Anyway, I type the code requested in the instructions and "SOFT" appears on the STB, as it should.
Yet, the blue bar shows no progresses whatsoever, until "SOFT" actuially stops appearing on the STB.
What am I doing wrong? The null modem cable is original (i.e. not hand made) and supposedly was intended for controlling STBs so I doubt it's not working.
I don't know what else to try.
I would like to do two things:
1) upload new keys
2) Organize channels
I think Gasoline is the software for "1". Not sure yet for "2", but if I can;t connect to the STB it does not matter much ...
Can anybody help?
Thank you in advance,
YankeeDDL
oui avec ca ceci sbcl
Hi
First you have to be sure which com port you have to use.
I'm pretty sure you are using a straightcable, you have to use a crossed rs232, pin 2 goes to 3 and 3 to 2, pin 5 goes to 5. You don't need more pin so I think you can make yourself one.
jtag ps8210 take a look here http://satsupreme.com/showthread.php?t=9830
and don't forget to speak english next time!
this is new firm ware. have a boot 15.01 and 20.0 than no problem.
Bonjour à tous,
Quelqu'un pourrait-il me dire quel est le dernier firm pour mon powersky 8210.
Je voulais également savoir si je pouvais utilisé sbcl v 0.9 avec aesupdater pour celui-ci.
sur mon 1500E ça fonctionne à merveille.
Merci d'avance
Hi, You just have to upgrade your 8210 with a firmware that is compatible with sharing. Yes it works like your 1500.
Next write in english thanx or post in french section
Posting Permissions
