Bulcrypt CAID 5581-част1

[drzdrz]

Наистина работи точно тази версия само че key-a за кпцс.дат е проблема , но с леко лъгане на сорса да види правилния ID ще стане. :)

Ако имаше сорс ще е лесно ,но сорс публичен няма . А да се прави ревърс а това байнари ... по мои наблюдения софта е от две "части" ( образно казано )
едната е криптирана , а другата не . Не криптираната е видима за всички - инита на картата , следва check за съсуржанието на дата файла и UUID. Мисля ,че тук трябва да се вмъкне брейк и да се гледа кой какво чете и какво чака да види . За съжаление смятам че и самото байнари е допълнително обработено ( цриптирано) та да не може да се прекара през HEX-едитор .Ако някой работи в това направление нека сподели .

[radionov]

Някои би ли ми обяснил по подробно как да направя пълен лог фаил на оскам , че при мен е много орязан. Четох някъде че се пише ( oscam -d255) но не знам къде.

[petar258]

стартираш оскам с команда "/пътядооскама/oscam -d 255" без кавички
или от web интерфейса кликаш на 255

[radionov]

стартираш оскам с команда "/пътядооскама/oscam -d 255" без кавички
или от web интерфейса кликаш на 255

Благодаря.

[tedy58]

стартираш оскам с команда "/пътядооскама/oscam -d 255" без кавички
или от web интерфейса кликаш на 255

да така е
/пътядооскама/./oscam -d 255

и лога си го задаваш къде да ти го прави примерно в директориите подолу във файла /etc/tuxbox/oscam.conf като там е целия лог, а не орязаният варант на това което виждаш в web interface-а прозореца,
примерно:

usrfile = /var/log/oscamuser.log
logfile = /var/log/oscam.log
cwlogdir = /var/log/cw.log

[Juliany112]

Може ли някои с карта и феникс да пробва тази пипната версия наOScam и след това да постне логовете.Благодаря предварително

http://www.satsupreme.com/download.php?id=222293

[astor1]

В lib-a на тази версия се говори за bulcrypt може пък да запали
reader-videoguard-common.o/
reader-tongfang.o/
reader-cryptoworks.o/
reader-videoguard12.o/
reader-videoguard1.o/
reader-bulcrypt.o/
reader-viaccess.o/
reader-videoguard2.o/
reader-nagra.o/ 1299509286 1000 1000 100644 21568

[mminkov]

Другарчета, нека и аз да напиша нещо тук по повод на разсъжденията. Става въпрос за връзката на 2 делти с COM порт (s200), няма ли някакав начин да се ползва служебното инфо през порта. Знае ли се изобщо какво върви на тези COM-ове когато има такава връзка (лично аз търсих, но нищо не намерих), и изобщо защо се прави тази връзка ако и 2-те делти трябва да са с актуални платени "черги". Надявам се да не ме увикате за мястото на писането, но поне на някой може да му дойде някаква идейка.

[drzdrz]

Може ли някои с карта и феникс да пробва тази пипната версия наOScam и след това да постне логовете.Благодаря предварително

http://www.satsupreme.com/download.php?id=222293

-------------------------------------------------------------------------------
>> OSCam << cardserver started at Tue Mar 8 10:23:39 2011
-------------------------------------------------------------------------------
2011/03/08 10:23:39 14702 s version=1.00, build #4795, system=i686-pc-linux, nice=-1
2011/03/08 10:23:39 14702 s max. clients=509, client max. idle=120 sec
2011/03/08 10:23:39 14702 s max. logsize=unlimited
2011/03/08 10:23:39 14702 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=120 ms
2011/03/08 10:23:39 14702 s shared memory initialized (size=4312366, id=62226446)
2011/03/08 10:23:39 14702 s auth size=4772
2011/03/08 10:23:39 14702 s Cannot open file ".//oscam.services" (errno=2)
2011/03/08 10:23:39 14702 s Cannot open file ".//oscam.user" (errno=2)
2011/03/08 10:23:39 14702 s signal handling initialized (type=sysv)
2011/03/08 10:23:39 14702 s can't open file ".//oscam.srvid" (err=2), no service-id's loaded
2011/03/08 10:23:39 14702 s can't open file ".//oscam.tiers" (err=2), no tier-id's loaded
2011/03/08 10:23:39 14702 s can't open file ".//oscam.provid" (err=2), no provids's loaded
2011/03/08 10:23:39 14702 s monitor: disabled
2011/03/08 10:23:39 14702 s camd 3.3x: disabled
2011/03/08 10:23:39 14702 s camd 3.5x: disabled
2011/03/08 10:23:39 14702 s cs378x: disabled
2011/03/08 10:23:39 14702 s newcamd: initialized (fd=6, port=34000, crypted)
2011/03/08 10:23:39 14702 s CAID: 5581
2011/03/08 10:23:39 14702 s provid #0: 000000
2011/03/08 10:23:39 14702 s cccam: disabled
2011/03/08 10:23:39 14702 s radegast: disabled
2011/03/08 10:23:39 14702 s logger started (pid=14703)
2011/03/08 10:23:39 14702 s reader started (pid=14704, device=/dev/ttyUSB0, detect=cd, mhz=357, cardmhz=357)
2011/03/08 10:23:39 14702 s waiting for local card init
2011/03/08 10:23:41 14704 r01 card detected
2011/03/08 10:23:45 14704 r01 ATR: 3B 20 00
2011/03/08 10:23:47 14704 r01 Maximum frequency for this card is formally 5 Mhz, clocking it to 3.57 Mhz
2011/03/08 10:23:48 14704 r01 [bulcrypt-reader] Bulcrypt card detected
2011/03/08 10:23:48 14704 r01 [bulcrypt-reader] type: Bulcrypt
2011/03/08 10:23:48 14704 r01 card system not supported
2011/03/08 10:23:48 14704 r01 Normal mode failed, reverting to Deprecated Mode





Ако имаш предложения за конфиг само кажи , веднага ще тествам .

[rionkov]

1 лог и от мен, карта-захаринка, нещо бърка атр.:

-------------------------------------------------------------------------------
>> OSCam << cardserver started at Tue Mar 8 13:16:46 2011
-------------------------------------------------------------------------------
2011/03/08 13:16:46 6497 s version=1.00, build #4795, system=i686-pc-linux, nice=-1
2011/03/08 13:16:46 6497 s max. clients=509, client max. idle=120 sec
2011/03/08 13:16:46 6497 s max. logsize=1000 Kb
2011/03/08 13:16:46 6497 s client timeout=10000 ms, fallback timeout=2500 ms, cache delay=0 ms
2011/03/08 13:16:46 6497 s shared memory initialized (size=4312366, id=2097153)
2011/03/08 13:16:46 6497 s auth size=4772
2011/03/08 13:16:46 6497 s Cannot open file "/var/tuxbox/build/oscam.services" (errno=2)
2011/03/08 13:16:46 6497 s userdb reloaded: 0 accounts freed, 1 accounts loaded, 0 expired, 0 disabled
2011/03/08 13:16:46 6497 s signal handling initialized (type=sysv)
2011/03/08 13:16:46 6497 s 825 service-id's loaded
2011/03/08 13:16:46 6497 s can't open file "/var/tuxbox/build/oscam.tiers" (err=2), no tier-id's loaded
2011/03/08 13:16:46 6497 s 6 provid's loaded
2011/03/08 13:16:46 6497 s monitor: initialized (fd=8, port=888, prio=1)
2011/03/08 13:16:46 6497 s camd 3.3x: disabled
2011/03/08 13:16:46 6497 s camd 3.5x: disabled
2011/03/08 13:16:46 6497 s cs378x: disabled
2011/03/08 13:16:46 6497 s newcamd: initialized (fd=9, port=61853, prio=1, crypted)
2011/03/08 13:16:46 6497 s CAID: 5581
2011/03/08 13:16:46 6497 s provid #0: 000000
2011/03/08 13:16:46 6497 s cccam: disabled
2011/03/08 13:16:46 6497 s radegast: disabled
2011/03/08 13:16:46 6497 s logger started (pid=6498)
2011/03/08 13:16:46 6498 l starting client 0 with ip 127.0.0.1
2011/03/08 13:16:46 6497 s reader started (pid=6499, device=/dev/ttyS6, detect=none, mhz=357, cardmhz=357)
2011/03/08 13:16:46 6497 s waiting for local card init
2011/03/08 13:16:46 6499 r01 starting client 0 with ip 127.0.0.1
2011/03/08 13:16:46 6499 r01 IFD: Opening device /dev/ttyS6

2011/03/08 13:16:46 6499 r01 standard baudrate: cardmhz=357 mhz=357 -> effective baudrate 1200
2011/03/08 13:16:46 6499 r01 IO: Setting properties

2011/03/08 13:16:46 6499 r01 IO: Setting DTR=1
2011/03/08 13:16:46 6499 r01 IO: Setting RTS=0
2011/03/08 13:16:46 6499 r01 IO: Receiving:
2011/03/08 13:16:47 7C
2011/03/08 13:16:47 6499 r01 IO: Receiving:
2011/03/08 13:16:47 TIMEOUT
2011/03/08 13:16:47 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:16:48 6499 r01 IFD: Initializing reader bulcrypt type=5

2011/03/08 13:16:48 6499 r01 standard baudrate: cardmhz=357 mhz=357 -> effective baudrate 9600
2011/03/08 13:16:48 6499 r01 IO: Setting properties

2011/03/08 13:16:48 6499 r01 IO: Setting DTR=1
2011/03/08 13:16:48 6499 r01 IO: Setting RTS=0
2011/03/08 13:16:48 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:16:49 6499 r01 IFD: Device /dev/ttyS6 succesfully opened

2011/03/08 13:16:49 6499 r01 ct_init on /dev/ttyS6: 1
2011/03/08 13:16:49 6499 r01 card detected
2011/03/08 13:16:49 6499 r01 IFD: Activating card in reader bulcrypt

2011/03/08 13:16:49 6499 r01 IFD: Resetting card:

2011/03/08 13:16:49 6499 r01 IFD: Phoenix Setting baudrate to 9600

2011/03/08 13:16:49 6499 r01 standard baudrate: cardmhz=357 mhz=357 -> effective baudrate 9600
2011/03/08 13:16:49 6499 r01 IO: Setting properties

2011/03/08 13:16:49 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:16:50 6499 r01 IFD: Setting parity from Even to Even

2011/03/08 13:16:51 6499 r01 IO: Setting RTS=1
2011/03/08 13:16:51 6499 r01 IO: Setting RTS=0
2011/03/08 13:16:51 6499 r01 IO: Receiving:
37
2011/03/08 13:16:51 6499 r01 IO: Receiving:
2011/03/08 13:16:51 03
2011/03/08 13:16:51 6499 r01 IO: Receiving:
2011/03/08 13:16:52 TIMEOUT
2011/03/08 13:16:52 6499 r01 ATR is malformed, it reports 3 historical bytes but there are only -1
2011/03/08 13:16:52 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:16:53 6499 r01 IFD: Setting parity from Even to Odd

2011/03/08 13:16:53 6499 r01 IO: Setting properties

2011/03/08 13:16:54 6499 r01 IO: Setting RTS=1
2011/03/08 13:16:54 6499 r01 IO: Setting RTS=0
2011/03/08 13:16:54 6499 r01 IO: Receiving:
37
2011/03/08 13:16:54 6499 r01 IO: Receiving:
2011/03/08 13:16:54 03
2011/03/08 13:16:54 6499 r01 IO: Receiving:
2011/03/08 13:16:55 TIMEOUT
2011/03/08 13:16:55 6499 r01 ATR is malformed, it reports 3 historical bytes but there are only -1
2011/03/08 13:16:55 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:16:56 6499 r01 IFD: Setting parity from Odd to None

2011/03/08 13:16:56 6499 r01 IO: Setting properties

2011/03/08 13:16:57 6499 r01 IO: Setting RTS=1
2011/03/08 13:16:57 6499 r01 IO: Setting RTS=0
2011/03/08 13:16:57 6499 r01 IO: Receiving:
37
2011/03/08 13:16:57 6499 r01 IO: Receiving:
2011/03/08 13:16:57 0D
2011/03/08 13:16:57 6499 r01 IO: Receiving:
2011/03/08 13:16:57 FF
2011/03/08 13:16:57 6499 r01 IO: Receiving:
2011/03/08 13:16:58 TIMEOUT
2011/03/08 13:16:58 6499 r01 ATR is malformed, it reports 13 historical bytes but there are only 0
2011/03/08 13:16:58 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:16:59 6499 r01 ATR: 37 0D
2011/03/08 13:16:59 6499 r01 ERROR: Could not read reader->convention
2011/03/08 13:16:59 6499 r01 Error activating card.
2011/03/08 13:17:00 6499 r01 IFD: Activating card in reader bulcrypt

2011/03/08 13:17:00 6499 r01 IFD: Resetting card:

2011/03/08 13:17:00 6499 r01 IFD: Phoenix Setting baudrate to 9600

2011/03/08 13:17:00 6499 r01 standard baudrate: cardmhz=357 mhz=357 -> effective baudrate 9600
2011/03/08 13:17:00 6499 r01 IO: Setting properties

2011/03/08 13:17:00 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:01 6499 r01 IFD: Setting parity from None to Even

2011/03/08 13:17:01 6499 r01 IO: Setting properties

2011/03/08 13:17:02 6499 r01 IO: Setting RTS=1
2011/03/08 13:17:02 6499 r01 IO: Setting RTS=0
2011/03/08 13:17:02 6499 r01 IO: Receiving:
37
2011/03/08 13:17:02 6499 r01 IO: Receiving:
2011/03/08 13:17:02 03
2011/03/08 13:17:02 6499 r01 IO: Receiving:
2011/03/08 13:17:03 TIMEOUT
2011/03/08 13:17:03 6499 r01 ATR is malformed, it reports 3 historical bytes but there are only -1
2011/03/08 13:17:03 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:04 6499 r01 IFD: Setting parity from Even to Odd

2011/03/08 13:17:04 6499 r01 IO: Setting properties

2011/03/08 13:17:05 6499 r01 IO: Setting RTS=1
2011/03/08 13:17:05 6499 r01 IO: Setting RTS=0
2011/03/08 13:17:05 6499 r01 IO: Receiving:
37
2011/03/08 13:17:05 6499 r01 IO: Receiving:
2011/03/08 13:17:05 03
2011/03/08 13:17:05 6499 r01 IO: Receiving:
2011/03/08 13:17:06 TIMEOUT
2011/03/08 13:17:06 6499 r01 ATR is malformed, it reports 3 historical bytes but there are only -1
2011/03/08 13:17:06 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:07 6499 r01 IFD: Setting parity from Odd to None

2011/03/08 13:17:07 6499 r01 IO: Setting properties

2011/03/08 13:17:08 6499 r01 IO: Setting RTS=1
2011/03/08 13:17:08 6499 r01 IO: Setting RTS=0
2011/03/08 13:17:08 6499 r01 IO: Receiving:
37
2011/03/08 13:17:08 6499 r01 IO: Receiving:
2011/03/08 13:17:08 0D
2011/03/08 13:17:08 6499 r01 IO: Receiving:
2011/03/08 13:17:08 FF
2011/03/08 13:17:08 6499 r01 IO: Receiving:
2011/03/08 13:17:09 TIMEOUT
2011/03/08 13:17:09 6499 r01 ATR is malformed, it reports 13 historical bytes but there are only 0
2011/03/08 13:17:09 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:10 6499 r01 ATR: 37 0D
2011/03/08 13:17:10 6499 r01 ERROR: Could not read reader->convention
2011/03/08 13:17:10 6499 r01 Error activating card.
2011/03/08 13:17:10 6499 r01 IFD: Activating card in reader bulcrypt

2011/03/08 13:17:10 6499 r01 IFD: Resetting card:

2011/03/08 13:17:10 6499 r01 IFD: Phoenix Setting baudrate to 9600

2011/03/08 13:17:10 6499 r01 standard baudrate: cardmhz=357 mhz=357 -> effective baudrate 9600
2011/03/08 13:17:11 6499 r01 IO: Setting properties

2011/03/08 13:17:11 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:12 6499 r01 IFD: Setting parity from None to Even

2011/03/08 13:17:12 6499 r01 IO: Setting properties

2011/03/08 13:17:12 6499 r01 IO: Setting RTS=1
2011/03/08 13:17:13 6499 r01 IO: Setting RTS=0
2011/03/08 13:17:13 6499 r01 IO: Receiving:
37
2011/03/08 13:17:13 6499 r01 IO: Receiving:
2011/03/08 13:17:13 03
2011/03/08 13:17:13 6499 r01 IO: Receiving:
2011/03/08 13:17:14 TIMEOUT
2011/03/08 13:17:14 6499 r01 ATR is malformed, it reports 3 historical bytes but there are only -1
2011/03/08 13:17:14 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:15 6499 r01 IFD: Setting parity from Even to Odd

2011/03/08 13:17:15 6499 r01 IO: Setting properties

2011/03/08 13:17:15 6499 r01 IO: Setting RTS=1
2011/03/08 13:17:16 6499 r01 IO: Setting RTS=0
2011/03/08 13:17:16 6499 r01 IO: Receiving:
37
2011/03/08 13:17:16 6499 r01 IO: Receiving:
2011/03/08 13:17:16 03
2011/03/08 13:17:16 6499 r01 IO: Receiving:
2011/03/08 13:17:17 TIMEOUT
2011/03/08 13:17:17 6499 r01 ATR is malformed, it reports 3 historical bytes but there are only -1
2011/03/08 13:17:17 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:18 6499 r01 IFD: Setting parity from Odd to None

2011/03/08 13:17:18 6499 r01 IO: Setting properties

2011/03/08 13:17:18 6499 r01 IO: Setting RTS=1
2011/03/08 13:17:19 6499 r01 IO: Setting RTS=0
2011/03/08 13:17:19 6499 r01 IO: Receiving:
37
2011/03/08 13:17:19 6499 r01 IO: Receiving:
2011/03/08 13:17:19 0D
2011/03/08 13:17:19 6499 r01 IO: Receiving:
2011/03/08 13:17:19 FF
2011/03/08 13:17:19 6499 r01 IO: Receiving:
2011/03/08 13:17:20 TIMEOUT
2011/03/08 13:17:20 6499 r01 ATR is malformed, it reports 13 historical bytes but there are only 0
2011/03/08 13:17:20 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:21 6499 r01 ATR: 37 0D
2011/03/08 13:17:21 6499 r01 ERROR: Could not read reader->convention
2011/03/08 13:17:21 6499 r01 Error activating card.
2011/03/08 13:17:21 6499 r01 IFD: Activating card in reader bulcrypt

2011/03/08 13:17:21 6499 r01 IFD: Resetting card:

2011/03/08 13:17:21 6499 r01 IFD: Phoenix Setting baudrate to 9600

2011/03/08 13:17:21 6499 r01 standard baudrate: cardmhz=357 mhz=357 -> effective baudrate 9600
2011/03/08 13:17:21 6499 r01 IO: Setting properties

2011/03/08 13:17:22 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:23 6499 r01 IFD: Setting parity from None to Even

2011/03/08 13:17:23 6499 r01 IO: Setting properties

2011/03/08 13:17:23 6499 r01 IO: Setting RTS=1
2011/03/08 13:17:23 6499 r01 IO: Setting RTS=0
2011/03/08 13:17:24 6499 r01 IO: Receiving:
37
2011/03/08 13:17:24 6499 r01 IO: Receiving:
2011/03/08 13:17:24 03
2011/03/08 13:17:24 6499 r01 IO: Receiving:
2011/03/08 13:17:25 TIMEOUT
2011/03/08 13:17:25 6499 r01 ATR is malformed, it reports 3 historical bytes but there are only -1
2011/03/08 13:17:25 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:26 6499 r01 IFD: Setting parity from Even to Odd

2011/03/08 13:17:26 6499 r01 IO: Setting properties

2011/03/08 13:17:26 6499 r01 IO: Setting RTS=1
2011/03/08 13:17:26 6499 r01 IO: Setting RTS=0
2011/03/08 13:17:26 6499 r01 IO: Receiving:
37
2011/03/08 13:17:26 6499 r01 IO: Receiving:
2011/03/08 13:17:26 03
2011/03/08 13:17:26 6499 r01 IO: Receiving:
2011/03/08 13:17:27 TIMEOUT
2011/03/08 13:17:27 6499 r01 ATR is malformed, it reports 3 historical bytes but there are only -1
2011/03/08 13:17:28 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:29 6499 r01 IFD: Setting parity from Odd to None

2011/03/08 13:17:29 6499 r01 IO: Setting properties

2011/03/08 13:17:29 6499 r01 IO: Setting RTS=1
2011/03/08 13:17:29 6499 r01 IO: Setting RTS=0
2011/03/08 13:17:29 6499 r01 IO: Receiving:
37
2011/03/08 13:17:29 6499 r01 IO: Receiving:
2011/03/08 13:17:29 0D
2011/03/08 13:17:29 6499 r01 IO: Receiving:
2011/03/08 13:17:29 FF
2011/03/08 13:17:29 6499 r01 IO: Receiving:
2011/03/08 13:17:30 TIMEOUT
2011/03/08 13:17:30 6499 r01 ATR is malformed, it reports 13 historical bytes but there are only 0
2011/03/08 13:17:30 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:31 6499 r01 ATR: 37 0D
2011/03/08 13:17:31 6499 r01 ERROR: Could not read reader->convention
2011/03/08 13:17:31 6499 r01 Error activating card.
2011/03/08 13:17:32 6499 r01 IFD: Activating card in reader bulcrypt

2011/03/08 13:17:32 6499 r01 IFD: Resetting card:

2011/03/08 13:17:32 6499 r01 IFD: Phoenix Setting baudrate to 9600

2011/03/08 13:17:32 6499 r01 standard baudrate: cardmhz=357 mhz=357 -> effective baudrate 9600
2011/03/08 13:17:32 6499 r01 IO: Setting properties

2011/03/08 13:17:33 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:34 6499 r01 IFD: Setting parity from None to Even

2011/03/08 13:17:34 6499 r01 IO: Setting properties

2011/03/08 13:17:34 6499 r01 IO: Setting RTS=1
2011/03/08 13:17:34 6499 r01 IO: Setting RTS=0
2011/03/08 13:17:34 6499 r01 IO: Receiving:
37
2011/03/08 13:17:34 6499 r01 IO: Receiving:
2011/03/08 13:17:34 03
2011/03/08 13:17:34 6499 r01 IO: Receiving:
2011/03/08 13:17:35 TIMEOUT
2011/03/08 13:17:35 6499 r01 ATR is malformed, it reports 3 historical bytes but there are only -1
2011/03/08 13:17:35 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:36 6499 r01 IFD: Setting parity from Even to Odd

2011/03/08 13:17:36 6499 r01 IO: Setting properties

2011/03/08 13:17:37 6499 r01 IO: Setting RTS=1
2011/03/08 13:17:37 6499 r01 IO: Setting RTS=0
2011/03/08 13:17:37 6499 r01 IO: Receiving:
37
2011/03/08 13:17:37 6499 r01 IO: Receiving:
2011/03/08 13:17:37 03
2011/03/08 13:17:37 6499 r01 IO: Receiving:
2011/03/08 13:17:38 TIMEOUT
2011/03/08 13:17:38 6499 r01 ATR is malformed, it reports 3 historical bytes but there are only -1
2011/03/08 13:17:38 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:39 6499 r01 IFD: Setting parity from Odd to None

2011/03/08 13:17:39 6499 r01 IO: Setting properties

2011/03/08 13:17:40 6499 r01 IO: Setting RTS=1
2011/03/08 13:17:40 6499 r01 IO: Setting RTS=0
2011/03/08 13:17:40 6499 r01 IO: Receiving:
37
2011/03/08 13:17:40 6499 r01 IO: Receiving:
2011/03/08 13:17:40 0D
2011/03/08 13:17:40 6499 r01 IO: Receiving:
2011/03/08 13:17:40 FF
2011/03/08 13:17:40 6499 r01 IO: Receiving:
2011/03/08 13:17:41 TIMEOUT
2011/03/08 13:17:41 6499 r01 ATR is malformed, it reports 13 historical bytes but there are only 0
2011/03/08 13:17:41 6499 r01 IO: Receiving:
TIMEOUT
2011/03/08 13:17:42 6499 r01 ATR: 37 0D
2011/03/08 13:17:42 6499 r01 ERROR: Could not read reader->convention
2011/03/08 13:17:42 6499 r01 Error activating card.
2011/03/08 13:17:43 6499 r01 card initializing error
2011/03/08 13:17:43 6497 s init for all local cards done