Dreambox - image, firm, soft, etj.

[keno135]

Po kerkoj filen e Mgcamd (qe te kete dhe Newcand list) per imazh Gemini E2 por nuk po arrij ta gjej dot. Me ndihmon dot njeri ju lutem ? Ju faleminderit.

[missoervin]

Progam FTP filezilla psh qe eshte free shkarko ketu

Cfar programi tjeter,

[receiveri]

Provo me nje program tjeter ftp sepse perderi sa ta ben ne dy box atehere ka probleme software.

Faleminderit

[mile kristo]

Cfare prog.ftp te per dore

perdor filezilla client

merre nga KETU

[keno135]

Mbarova pune. Ishte i quajtur me emrin GP3 dhe versioni me i larte ishte 1.36. Si duket nuk eshte updatuar me versionet e fundit.

[OVES12]

Because it over and over and over again are questions I have to MGCamd here's a quick example. Basically, all the parameters are very well explained in the config to "read only" must.

Used to edit or create files Notepad + +

The following mg_cfg should run on all E2 boxes sh4.

MGCamd uses different config files.
The most important is:

mg_cfg -> File Hauptconfig
newcamd.list -> is needed for a newcamd compound
cccamd.list -> is needed for a cccam compound
ignore.list -> to prevent unnecessary requests optional
priority.list -> optional for Priorisierenvon CAID's
replace.list -> option is used for mapping of CAID's


For the relevant log entries but optional
Entries which often lead to mistakes or misunderstanding

P: select order of network protocols. Basically, the number is correct in the protocol used by you at the most forward
Q: Can the solution for problems with HD + and other HD channels. This often helps to try just once

The most feared and always missed setting the network protocol!

01 = Newcamd Protocol (newcamd.list)
32 = cccam protocol (cccamd.list)
33 = newcamd + cccam protocol because 01 + 32 = 33

This has just the right receiver to be selected. Sometimes you have a different image depending on the test. So, the settings between E2, or original neutrino may be different


mg_cfg

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 00 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } root newcs

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 8080

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 02 } 127.0.0.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 11 }

# map all 180x nagra caids to 1801
# default is 01
F: { 00 }

newcamd.list

Here is how I've mentioned above to connect to a newcamd server made​​.

CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = <Serveradresse> <Port> <Username> <Passwort> <Deskey>
CWS_MULTIPLE = <Serveradresse> <von_Port:bis_Port> <Username> <Passwort> <Deskey>

Here is an example

CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = 192.168.1.1 20000 dummy dummy 10 02 13 04 15 06 17 08 01 10 11 12 13 14
CWS_MULTIPLE = 192.168.1.2 20000:20005 dummy dummy 10 02 13 04 15 06 17 08 01 10 11 12 13 14

Multiple CWS can be used if you want to connect to multiple ports on a shared server newcamd. The incoming port can be neglected.

cccamd.list

#Example of a cccamd.list
#C: <Serveradresse> <Port> <Username> <Passwort>
C: 172.16.1.1 12000 user1 pass1

Here a connection to a cccam server is made.
In theory, you must be the only cccamd.list its C: pure line and you can copy it go off.

replace.list

# replace old caid > newcaid example
# X: {{ CAID } { CAID }}
X: {{ 1833 } { 1702 }}

Here, the CAID 1702 is mapped to the CAID 1833rd That is necessary if it is not already done on the server.

ignore.list

# ignore this caid
#X: { CA ID }
#Beispiel S02
X: { 18 31 } #Premiere (old)
X: { 17 22 } #SKY KD
X: { 09 8E } #SKY KabelBW
X: ( 09 C4 } #SKY V13

The CAID ignore.list be ignored and is then needful when there are many wrong questions. Normally you can ignore this though.

priority.list

# use this caid first
#X: ( CA ID }
X: {1702} #SKY S02
X: { {1833} {1702} } #SKY S02 HD
X: {1830} #HD+

Here's CAID can be prioritized. The file is also optional.

All with no guarantees ... I am getting also like to improve or supplement.
This should be as much as 80% of the questions to be solved ....

[receiveri]

Faleminderit shume per ndihmen

perdor filezilla client

merre nga KETU

[receiveri]

Me kete prog. filezillasi mund te hap Cccamin per te ndryshuar apo me rualtur, sikur tek Prog.DCC

[mile kristo]

Me kete prog. filezillasi mund te hap Cccamin per te ndryshuar apo me rualtur, sikur tek Prog.DCC

po pa problem

[M-P]

nje imazh te mire per dm 800 hd sim 2.01. kam vendos edg nemesis 2.1 po ma nxiu.. flm