Phoenix V1.0.17

[lezwez]

V1.0.17 Phoenix Patch For Reality Cam 16-06-05

--------------------------------------------------------------------------------

Phoenix V1.0.17


*******************************
***WARNING!! WARNING!! WARNING!!***
*******************************
* OmniKrypt V1.0.5 REQUIRED! This patch will not work on previous versions.
To check whether you have OmniKrypt V1.0.5, go into the CAM main menu, and see if there is "Welcome V1.0.5" on top of the screen.

NOTE : OmniKrypt V1.0.5 available via OTA download on Dptv 12.092H Hotbird 13east since 16/06/2005.


* Seems like new OmniKrypt supports Premiere official card now.
* Spice Platinum work around in Phoenix->Utility menu.
This will turn TPS 007C00 provider back on. Please note that when you do not have the correct TPS AES Key, this will break most of the channels in TPS (i.e.Multivision)
* Updated keys





PLEASE NOTE AFTER UPGRADE YOU MUST GOTO INFORMATION IN THE CAM MENU AND PRESS OK/SELECT TO ACTIVATE THE PATCH

[lezwez]

There is a problem with the short CI initialization time on Humax 5x00 series STB when
upgrading RealityCAM with Phoenix. We are able to find a workaround, but this will require
a little bit more effort on your part when upgrading RealityCAM in your Humax STB.

Please follow the instruction below :

(Step 1)

Tune to a FTA channel.

(Step 2)

a. Upgrade/download the .upd or .hex file in folder "update file 1"
b. Goto CI menu->OmniKrypt->Information menu, and you will see "Press OK to copy update file 1".
Press OK! After around 10-20 seconds, the CAM will reset.
c. Goto CI menu->OmniKrypt->Information menu again, and check if you see "Please download update file 2".
If yes, please proceed to (Step 3)

(Step 3)


a. Upgrade/download the .upd or .hex file in folder "update file 2"
b. Goto CI menu->OmniKrypt->Information menu, and you will see "Press OK to copy update file 2".
Press OK! After around 10-20 seconds, the CAM will reset.
c. Goto CI menu->OmniKrypt->Information menu again, and check if you see "Please download update file 3".
If yes, please proceed to (Step 4)

(Step 4)

a. Upgrade/download the .upd or .hex file in folder "update file 3"
b. Goto CI menu->OmniKrypt->Information menu, and you will see "Press OK to copy update file 3".
Press OK! After around 10-20 seconds, you will see "Press OK to begin image-copy-over & reboot".
Press OK again! After around 20-30 seconds, the CAM will reset.

(Final step)

Goto CI menu->OmniKrypt->Information menu, and press OK to activate Phoenix. Enjoy

[lezwez]

Phoenix V1.0.17a



***********************************
***WARNING!! WARNING!! WARNING!!***
***********************************
* OmniKrypt V1.0.5 REQUIRED! This patch will not work on previous versions.
To check whether you have OmniKrypt V1.0.5, go into the CAM main menu,
and see if there is "Welcome V1.0.5" on top of the screen.

NOTE : OmniKrypt V1.0.5 available via OTA download since 6/16/2005.

* Polsat fixed

Full.Zip Includes (+ patch for HUMAX users)

1) .Upd - PCMCIA / PCB Serial Programmer.
2) .Hex - Smart card download using Fun5 / Fun6 / Fun7 cards.
**Erase the Fun7 card clean before it will program right with CAS2**
3) README



PLEASE NOTE AFTER UPGRADE YOU MUST GOTO INFORMATION IN THE CAM MENU AND PRESS OK/SELECT TO ACTIVATE THE PATCH:-]

[lezwez]

FullThere is a problem with the short CI initialization time on Humax 5x00 series STB when
upgrading RealityCAM with Phoenix. We are able to find a workaround, but this will require
a little bit more effort on your part when upgrading RealityCAM in your Humax STB.

Please follow the instruction below :

(Step 1)

Tune to a FTA channel.

(Step 2)

a. Upgrade/download the .upd or .hex file in folder "update file 1"
b. Goto CI menu->OmniKrypt->Information menu, and you will see "Press OK to copy update file 1".
Press OK! After around 10-20 seconds, the CAM will reset.
c. Goto CI menu->OmniKrypt->Information menu again, and check if you see "Please download update file 2".
If yes, please proceed to (Step 3)

(Step 3)


a. Upgrade/download the .upd or .hex file in folder "update file 2"
b. Goto CI menu->OmniKrypt->Information menu, and you will see "Press OK to copy update file 2".
Press OK! After around 10-20 seconds, the CAM will reset.
c. Goto CI menu->OmniKrypt->Information menu again, and check if you see "Please download update file 3".
If yes, please proceed to (Step 4)

(Step 4)

a. Upgrade/download the .upd or .hex file in folder "update file 3"
b. Goto CI menu->OmniKrypt->Information menu, and you will see "Press OK to copy update file 3".
Press OK! After around 10-20 seconds, you will see "Press OK to begin image-copy-over & reboot".
Press OK again! After around 20-30 seconds, the CAM will reset.

(Final step)

Goto CI menu->OmniKrypt->Information menu, and press OK to activate Phoenix:-]