newcs_1.18 crashing with d+ official card

[cocoa117]

hi, i found problem with d+ card using with newCS_1.18. It seems the newCS never really finished the initial booting process. It hang at the message as following

TCP-log password is disabled!
level: normal
type: init
output: console
logger config: level 1 type 3 output 1
Console log options: level 1 type 3
[ 00:49:35 ] [ Box detect ] Box type 2
[ 00:49:35 ] [ Config ] Option <mhz> for device 0 (lower) not present, defaulting to 357
[ 00:49:35 ] [ Config ] Option <sid> for device 0 (lower) not present, no static sids added to filter
[ 00:49:35 ] [ Config ] /dev/sci0 ECM priority: crypto-special
[ 00:49:35 ] [ Config ] Option <mhz> for device 1 (upper) not present, defaulting to 357
[ 00:49:35 ] [ Config ] Option <sid> for device 1 (upper) not present, no static sids added to filter
[ 00:49:35 ] [ Config ] /dev/sci1 ECM priority: crypto-special
[ 00:49:35 ] [ Config ] Option <spider> not present for User: bytech, defaulting to NO
[ 00:49:35 ] [ EMM Cache ] Initialising Cache with 10 entries
[ 00:49:35 ] [ ECM Cache ] Initialising Cache with 10 entries
[ NewCS ] Process ID is: 759
[ 00:49:35 ] [ Loader ] Reader type 5 on node /dev/sci0
[ 00:49:35 ] [ Sci ] Opening device /dev/sci0
[ 00:49:35 ] [ Sci ] CARD_DETECT for sci returned 1
[ 00:49:37 ] [ Loader ] Init Nagra card
[ 00:49:37 ] [ Keyman ] Adding key xxxxxxxx type 0 on Provider 0 for caid 1800 ID=0
[ 00:49:37 ] [ Keyman ] Adding key xxxxxxxx type 1 on Provider 4001 for caid 1800 ID=0
[ 00:49:37 ] [ Keyman ] Adding key xxxxxxxx type 1 on Provider 4101 for caid 1800 ID=0

Normally it should finish the booting by saying
[ NewCS ] Ready to GO!

But with Digital+ card, it never get to that stage.

I changed the priority to hard, crypto-special and pthandshake, but it have same problem.

Any idea?

[the peppi]

hi, i found problem with d+ card using with newCS_1.18. It seems the newCS never really finished the initial booting process. It hang at the message as following

TCP-log password is disabled!
level: normal
type: init
output: console
logger config: level 1 type 3 output 1
Console log options: level 1 type 3
[ 00:49:35 ] [ Box detect ] Box type 2
[ 00:49:35 ] [ Config ] Option <mhz> for device 0 (lower) not present, defaulting to 357
[ 00:49:35 ] [ Config ] Option <sid> for device 0 (lower) not present, no static sids added to filter
[ 00:49:35 ] [ Config ] /dev/sci0 ECM priority: crypto-special
[ 00:49:35 ] [ Config ] Option <mhz> for device 1 (upper) not present, defaulting to 357
[ 00:49:35 ] [ Config ] Option <sid> for device 1 (upper) not present, no static sids added to filter
[ 00:49:35 ] [ Config ] /dev/sci1 ECM priority: crypto-special
[ 00:49:35 ] [ Config ] Option <spider> not present for User: bytech, defaulting to NO
[ 00:49:35 ] [ EMM Cache ] Initialising Cache with 10 entries
[ 00:49:35 ] [ ECM Cache ] Initialising Cache with 10 entries
[ NewCS ] Process ID is: 759
[ 00:49:35 ] [ Loader ] Reader type 5 on node /dev/sci0
[ 00:49:35 ] [ Sci ] Opening device /dev/sci0
[ 00:49:35 ] [ Sci ] CARD_DETECT for sci returned 1
[ 00:49:37 ] [ Loader ] Init Nagra card
[ 00:49:37 ] [ Keyman ] Adding key xxxxxxxx type 0 on Provider 0 for caid 1800 ID=0
[ 00:49:37 ] [ Keyman ] Adding key xxxxxxxx type 1 on Provider 4001 for caid 1800 ID=0
[ 00:49:37 ] [ Keyman ] Adding key xxxxxxxx type 1 on Provider 4101 for caid 1800 ID=0

Normally it should finish the booting by saying
[ NewCS ] Ready to GO!

But with Digital+ card, it never get to that stage.

I changed the priority to hard, crypto-special and pthandshake, but it have same problem.

Any idea?

i think you miss the boxkey in youre config
if i am correct its nagra or is it the seca card on 19e?
and is this on youre dreambox or on the linux pc?