Linbox avira 300 hd boot

[santana-bg68]

Здравеи те на всички,имам нужда от помош не мога да пермехна тоя( боот) една година ме мъчи Благодаря на всички предварително...

[turbopower]

How to upgrade SW box only if your display 'boot'
Check it follow the below steps
1.Prepare
A.STB connected to PC via RS232
B.Open Hyper Terminal base on your PC, set the UART baud rate is 115200, no odd-even, 1 stop bit.
2.Enter u-boot mode and input command in Hyper Terminal
A.Press "@ + Space" to make STB stop in uboot when startup
B, Then input command 'Run menu', you will see these options,
STB225v1 nand # run menu
Select your Bootmode:
1: Load the kernel from Flash and FS from NFS
2: Load the kernel from Flash and FS from Flash
3: Load the kernel from NFS and FS from NFS
4: Failsafe from secondary flash image
Please enter 'bootchoice':
C, please input '4 ', then press' enter',
3.plug in a USB stick Including upgrade file.
4.reboot the receiver, will automatically upgrade SW.

Тук казват така ако не си го изпробвал. Нямам такъв приемник попадна ми информацията от търсачка.

[santana-bg68]

Пробвах но нестава или аз нешто бъркам

[dstb]

Здравеи те на всички,имам нужда от помош не мога да пермехна тоя( боот) една година ме мъчи Благодаря на всички предварително...

Какво значи: "не мога да пермехна тоя( боот)" ?
Друг ли искаш да сложиш, или какво ???

[santana-bg68]

Какво значи: "не мога да пермехна тоя( боот)" ?
Друг ли искаш да сложиш, или какво ???

Искам да го подкарам но нешто нестава след като го стартирам на екрана да тв стои лого linbox и до там как не го мачих как да го подкарам........

[santana-bg68]

-- Generic Primary Bootloader 0.1-3847, NI (04:13:33, Feb 17 2009)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 0 (expecting 2)
Poly10: 0x00000000
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 00000000000000000000000000000000
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 512 cols x 8192 rows: 64 MBytes
SIF1: 512 cols x 8192 rows: 64 MBytes
DRAM: 200 MHz, 2 x 64 MBytes: 128 MBytes
NAND: RDY polling disabled
NAND: (AD76) Hynix SLC, pagesize 512, blocksize 16k, 64 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: valid image
aboot exec time: 214378 uSec


U-Boot 1.2.0.0428_a (Secondary Bootloader) (Jul 19 2010 - 14:51:26)

CPU: PNX????
Secure boot: disabled
DRAM: 128 MB
NAND: nCS0 (force asserted legacy mode)
NAND: Hynix 64MiB 3,3V 8-bit
init scart chip uda3000.
init scart chip on i2c 1 bus.
init hdmi on i2c 1 bus.
Net: ip3902
Board Opts: EthOsc SCART HDMI PAL
Splash: done
u-boot startup time so far: 1082 msec
Hit any key to stop autoboot: 1  0

STB225v1 nand# ##

STB225v1 nand# run menu (????????????????????)
## Error: "menu" not defined

STB225v1 nand# 4 (???????????????????)
Unknown command '4' - try 'help'

STB225v1 nand# rebooty (???????????????????)
--------------------------------------------------------------------
-- Generic Primary Bootloader 0.1-3847, NI (04:13:33, Feb 17 2009)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 0 (expecting 2)
Poly10: 0x00000000
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 00000000000000000000000000000000
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 512 cols x 8192 rows: 64 MBytes
SIF1: 512 cols x 8192 rows: 64 MBytes
DRAM: 200 MHz, 2 x 64 MBytes: 128 MBytes
NAND: RDY polling disabled
NAND: (AD76) Hynix SLC, pagesize 512, blocksize 16k, 64 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: valid image
aboot exec time: 214378 uSec


U-Boot 1.2.0.0428_a (Secondary Bootloader) (Jul 19 2010 - 14:51:26)

CPU: PNX????
Secure boot: disabled
DRAM: 128 MB
NAND: nCS0 (force asserted legacy mode)
NAND: Hynix 64MiB 3,3V 8-bit
init scart chip uda3000.
init scart chip on i2c 1 bus.
init hdmi on i2c 1 bus.
Net: ip3902
Board Opts: EthOsc SCART HDMI PAL
Splash: done
u-boot startup time so far: 1082 msec
Hit any key to stop autoboot: 1  0

Loading from 64MiB 3,3V 8-bit, offset 0x1a0000
Automatic boot of image at addr 0x80800000 ...
## Booting image at 80800100 ...
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 1569752 Bytes = 1.5 MB
Load Address: 80001000
Entry Point: 802a84a0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ... Моля помогнете,как да я подкарам тая барака,(Linbox avira 300 hd boot)

[turbopower]

Пробвай да намериш от някъде dump от работещ flash и чрез програматор или JTAG го запиши на твоят flash.