Triple Dragon image

[PAN]

new off image 2005 07 12
8MB_.bin
-----------------------------------
- change: to unprotect PIN-checks, set the PIN to 0000 in expert menu.
- new: in manual-scan frequency can decreased/increased with the left/right
cursor keys. If tuner is locked, each keypress steps by 125 KHz. If
the tuner is not locked to a digital carrier, the stepwidth is 1 MHz.
- new: In manual-scan the symbolrate can decreased/increased with the left/
right cursor key im 1 kS/s steps.
- new: in manual scan are two new bars. The upper one shows the frequency
offset between the tuned frequency and the messured center frequency.
The second bar shows the ofset of the symbolrate between tuned SR and
the real messured SR. If the frequency/SR is to low, the marker is at
the left side from the center. If the frequency/SR is to hight, the
marker is at the right side of the center. Both bars shows only
correct values, if the tuner is locked to a digital carrier !
- bugfix: With a small patch to the used glib a lot of timing bugs are fixed.
The most visible difference is the infobar after a channel change. This
will not be hide before the time setup in the OSD-setup menu, but in
fact, this will stabilize a lot of internal timings such as the filters.
- update: updated greek translation. Thanks to our greek friends !

8MB_image_0_9_8-3_16-2005_07_06.bin
-----------------------------------
- change: if a PIN (to protect services) ist set, also the setup/installation
menus are only accessible after entering the correct PIN.
- new: Hotplug-devices (USB) gives a short message on the screen if attached
or removed

tdimage_2005_07_02.bin
----------------------
- new: most completely rewritten code for USB (both storage and WLAN).
Read the usb-readme.txt file for more informations.
- new: Initial work for parental rating. Navigate to Menu -> Maintain Lists ->
Maintain Favorite Lists and create a list with the name PIN. All the
services you add to this list are pin-protected. Services have only
to be unlocked after each power-on. To change the pin, navigate to
the expert menu. The default pin is 0000.

tdimage-tdkernel_0_9_7-2005_06_29-2.bin
---------------------------------------
- bugfix: fixed all that blocking caused by the Samba server start/stop actions.
For detailed informations about network- and samba related stuff,
read the network-readme.txt in this ZIP-archive.

tdimage_2005_06_26.bin
----------------------
- new: there is a Samba-server included now. This one can be configured
from the GUI of course.
- bugfix: if the network was not configured at all the network configuration
menu takes the values from bootloader for the embedded network card.
The USB-WLAN is setup to 10.1.1.254/24 by default.
- bugfix: while the STB is booted and running from an NFS-share, the network
setup does not allow changes to the configuration for the embedded
network card, because this will kill the NFS-connection.
- bugfix: AC3 and DTS audio-services are restored correctly now from the saved
value in the settings.
- change: various providers sends stupid short-EI and scheduling data, which
caused wrong localized characters. Added handling for more of such
providers.
- change: added some more language-codes (some not defined by ISO) mainly for
eastern europe countries.

[PAN]

Some notes about the network configuration:

network interface configuration:
if the network interface is running in a simple local network without
any gateway(s) to other networks like the internet, set the gateway-
address to the same one, you use for the IP-address of the interface.
Never set the gateway to 0.0.0.0 or 127.0.0.1 (localhost).

If there is no DNS available in the network, set the DNS-address to
127.0.0.1 (localhost) to prevent long times for name lookups.

Samba server configuration:
You have to call this at least once, to get samba working. If you only
enable the Samba server and save this with the default values, your STB
will be visible inside a MS Windows network, but you are not able to
access the server, because there is no password set. So you have to
enter the password you wanna use before you save the config. Of course,
this is only necessary once.

Samba special notes:
If you change any settings in the Samba configuration and you have accessed
the server before by a Windows client (i.e. MS Windows 98, 2000, XP), it
can happen, that you are not able to access the server from this client
for a very long time (several hours). This is because Windows clients are
really slow sometimes in updating their server list.

If you change the username and/or the password and you are logged into the
server, it's a good idea to restart the Windows client, because Windows is
caching the last used login username/-password and will not detect your
change. In this case you will only get an "access denied" message from your
Windows client.

Samba do not accept passwords with special character. Only latin characters
and numeric characters are allowed.

If you are using really old Windows 95 clients, do not forget to install
the network security patch from Microsoft. This Samba server uses
encrypted passwords, but the original Windows 95 version without that
patch only transmit passwords in plain format over the network.

Und nun noch der Inhalt der usb-readme.txt / And now, the content of the usb-readme.txt:

Since the Linux-Kernel 2.6.12 our old code to mount USB-storage devices wan't
work at all, because the kernel now makes a lot of test before a device becomes
available to the userspace. For a typical device this takes up to 6 seconds. The
older kernels only needs less than a half second. So this kernel change was a
good cause to rewrite most of the USB-hotplugging stuff. Now there is a new
/sbin/hotplug kernel-helper, which handles all the necessary hotplug stuff for
storage devices and networking. This helper also integrates an automounter for
SCSI-devices. Remember, all USB storage-devices are emulated SCSI-devices in the
Linux-enviroment. So, the main-application needs no additional time anymore for
the USB-subsystem except for loading plugins from such devices.

With this new USB-handling also the naming is changed. In /mnt/usb you will see
all USB-storage devices in the naming "SCSI-device-name - Vendor - Model", where
"SCSI-device-name" is sda1, sda2, sdb4 or something els beginning with "sd".
"Vendor" typically is the manufactor of the device and "Model" is the description
given by the manufactor.

[passete]

tdimage_2007_05_03.bin (min. requiered: 8MB_image_0_10_0-3_29-2005_11_15)--------------------------------------------------------------------------------- bugfix: requesting a reload of timer events from file caused a crash.- new : new command trl in tdcontrol to reload timer events from network.tdimage_2007_04_29.bin (min. requiered: 8MB_image_0_10_0-3_29-2005_11_15)--------------------------------------------------------------------------------- bugfix: file-browser for PVR-playback did not allow deleting of files without the counter in the suffix (.xx.ts)- new : added 2x, 4x, 8x icons ffor FF/FR in Timeshift- new : while a running recording pressing the red hand timeshift) button switches into timeshift mode and starts playback of the current recording but from the beginning of the file.- bugfix: embedded CA for Conax smart cards could run into an race conditiontdimage_2007_03_20.bin (min. requiered: 8MB_image_0_10_0-3_29-2005_11_15)--------------------------------------------------------------------------------- bugfix: bugtracker entry #0000045. Spectrum-Analyzer crash.- bugfix: bugtracker entry #0000026. PVR-Playback was not able to handle files without a segment number in the flename suffix.- bugfix: bugtracker entry #0000022. Timeshift A/V fully out of sync afer FF.- bugfix: bugtracker entry #0000042. Video bitrate display- bugfix: bugtracker entry #0000041. menus got broken, if more than 1 page exist.- bugfix: bugtracker entry #0000039. Crash after pressing EPG-button, if no services exist.- bugfix: bugtracker entry #0000028. Missin characters in input dialogs.- rework: The PVR-Playback and Timeshift code is fully rewritten and solves multiple prroblems: - Fast forward/rewind in Timeshift works. - buttons for PVR and Timeshift also works, if the infobar is visible. - audio-muting is handled correct. - fast forward rewind works (hopefully) on all streams. Please note: fast rewind may stop in 2x mode on some streams. Simply switch to 4x or 8x to solve that. - percentage jums are also aailable in Timeshift. - percentage jumps can be initiated if playback is paused (still image). - if playback reaches the end of file, it's possible to rewind or jump (percentage or by label) - Playback of TS-files without an counter in the suffix is possible.- new : in HDD option menu, new option to set the sort-order in the File browser for PVR-Playback- new : in NAS setup menu, new option to select NAS as the destination ffor PVR- recordings.-change : added XFS-support for the PVR-partiton (used as default).

[passete]

Dragon team image v4.1a
New Dragon team image based on the latest official image

var - 2.0MB

1. Fixed script to addon doawnload in menuxml plugin because board change adress.
2. New na-start.sh, now after emu restart you don't need to change channel to see picture.
3. Fixed downloading web interface from internet browser
4. New xml plugin, thx @magumagu for new option
5. New position in backup option "Restore all setup" This position give us possibility restore all setup.
a. creating keys and setting copy on USB or HDD
b. intall image
c. set network adress
d. download xmlmenu
e. restore all setup

6. opptimalisation xmlmenu

a. now xml check after 10 run if is new version.
b. new option Q - closing plugin
c. new option L - light line in peers

[passete]

TDman v5d gbx !

Based on latest official image.
8mb image, no need to install 8mb official.

Remember to backup Your settings before updating!!


* No emu included inside. Copy gbx to /var/bin chmod755 and reboot box to start it working.
* Left samba stuff (not deleted)
* Removed skins, Thx to Crash left one made for me as default.
* Plugins, skins and lang files moved to /var partition.
* Plugins dedicated for gbx included.
* CAIc plugin a little bit reworked.
* VAR partition size ~ 2,6MB
* Keys as always for reference. Update on Your own.


One thing more. Sometimes You have problems with channels and favorites list. It is due changes in format of them.
Scan once again orbit and make new one.


Note: If some people are using this readme in their own releases please don't forget to
notice from what release they are taking it, or write their own file.

[passete]

BD Team InjectoR v1.9

* Based on the last official image
* Removed all languages files except English
* Removed all skins except Default skin (Mod'd Crash by devel).
* No emus, no keys, no roms inside
* Radegast, Evocamd, Mgcamd, Newcamd, Newcs, Laufvogel and Cs2**** support
* Increased /var directory size to 2.3 mb.
* Added Menu xml for download
- You can now install Plugins in USB or in FLASH
- You can install Emus in USB or in FLASH
- And somes others stuffs
* Added Web-interface v1.9
- You can now install Plugins in USB or in FLASH
- You can install Emus in USB or in FLASH
- And somes others stuffs
* Secure Httpd server:
- user : Injector
- password: bdteam
- to change password, use telnet command:
root@dbs3000:/bin# httpd -A /var/etc/.InjectoR TD-Injector-Server Injector "Your Password"

[passete]

Revised 5C Image

has latest MGCAMD, EVOCAMD, NEWCS

[passete]

v5g std

Based on latest official image.
8mb image, no need to install 8mb official.

Remember to backup Your settings before updating!!


* Introducing new versions of newcs, evocamd made for TD.
* New noalco plugin (no more warm reboot in menu) It is seen as PMT Plugin.
* Removed samba stuff (You can still use it, just copy binaries to /var/bin and chmod755)
* Removed skins, Thx to Crash left one made for me as default.
* Plugins, skins and lang files moved to /var partition.
* Bmtoy ver. 4.99b
* VAR partition size ~ 2MB
* Keys as always for reference. Update on Your own.


One thing more. Sometimes You have problems with channels and favorites list. It is due changes in format of them.
Scan once again orbit and make new one.


Note: If some people are using this readme in their own releases please don't forget to
notice from what release they are taking it, or write their own file.

Enjoy. Tdman

[zanzibare]

nexus0.2_moon
New nexus image, based on the latest official image.

@+++++++

[skogly]

I have tried this img. Think there is a bug whith IPKG, it does not work for me.
Another problem I did,t found out was how I coud start emu. Put an emu in var/bin, but still only CI was displayd.
So this I coud not use.