Solution for dead strong

[christopher11]

In french

[mohamed6355]

Is there an English version of this?

[modibbo1]

hi.
pls also my receiver is death after upgrading,4651x,i need solution also in english help

[urmans]

Upgrade with the latest software... (if the latest damage use previous one)

1. STB Off
2. CLICK Start Download Firmware
3. STB On

[modibbo1]

hi.
my receiver can not even bring light after upgrading it with new software 4651x.how can repair it.just nothing no light.

[buwang]

please help . . .

my box (srt4650) didnt work after downloading new softkey, i tried to restore and download old softkey, it not accepting, my box hang and didnt turn on.

please help and please tell me what to do....

Brothers, mates, expert your assistance is highly appreciated.

[mghondory]

please help . . .

my box (srt4650) didnt work after downloading new softkey, i tried to restore and download old softkey, it not accepting, my box hang and didnt turn on.

please help and please tell me what to do....

Brothers, mates, expert your assistance is highly appreciated.

Dear My friend, your box likely is Chinese, so I think you must have a new flash on your box. I hope it'll be Ok soon. bye

[buwang]

mghondory my friend,

thanks ... i've figured it out and solve my problem. thanks again for the concerned being shown.

[spartaqus]

can i get help?my strong str8000 is dead after flash failure (it is not turning on at all)

[foudre]

HEfc0.flash VOOR DODE STRONG opgehaald bij www.firm-collector.com / strong/bfc0.flash
VOOR DODE STRONG BFCO.rar
Always check whether the receiver is even a sign of life,
connect the receiver via the door to a com pc and see if the loader
give a reaction after the receiver has been light (such as that which gives when the
Receiver has received a new software.)
this is important if a communication is possible.
When we managed to connect the receiver mode CHA (charge),
and also that the display does not turn, try to load again softawe.
It may be that the receiver detects a fault in the software
and that the receiver wants to restart.
If that does not work, try the next thing
It may be that the loader does not command close to the receiver, and therefore
the receiver still await data.
We can try to complete the software manually upload.
be as follows:
1. Putting Receiver mode CHA-mode (expense)
2. Start programme loader2000 and choose the right door com.
3. Insert bottom of the screen of the loader in small letters the following codes without
description which is obviously after!
-- "H" you get a response back, then:
-- Several times "Ctrl + C" to get a message and then:
-- "G" do you display back?
When it does not, restart the receiver a new mode CHA, and
reload the software.
In some cases the previous points are not enough, try:
1. Start Hyperterminal and that set it properly.
Bits per second = 38400
Databits = 8
Pariteit = no
Stopbits = 1
Datatransport besturing = Xin / Xout
2. To liaise with the recpteur.
3. Tap a button
4. Wait a message like "Access Code?" (Receiver request an access code)
5. Enter the access code "cafe" (without the quotes and only if DeadCafe 3.0
is used on recpeteur.
6. When the device asks "enter access code?" , Go to point 3
When you are logged:
7. Touch "c" the receiver think it will now receive a file.
8. Close Hyperterminal.
9. Démarer loader2000 and load the software.
After loading, it is possible that the display still does nothing, then restart
Receiver and the display will return.
Sometimes this is not a problem of soft but a capacitor that does not work
correctly.
the capacitor is a finding on the circuit behind the front panel.
the capacitor can lead to error on the microcontroller, which must give at the
Request a reset pulse to the microprocessor of the table.
the solution is to allow the capacitor empty for the microcontroller operates a
new.
following steps:
1. Disconnect the receiver and open.
2. Remove the display on the front and collect the 0.22 uF capacitor, which is used
as battery (it is green and is forming a battery)
3. Close the two pines for a few seconds (save a contact between the two pines)
4.refermer the receiver and not forget to hand the detailed display
5. When you power up the receiver, and that the display gives "OK", it is now possible to
load the software
It may (and often happens!) That quartz, which is coupled with the microcontroller on the
panel display is defective. when it does not work, the microcontroller can not
give command reset the microprocessor.
quartz has a frequency of 32.768 kHz.
it is a small silver tube color (?) with 2 legs.
it is welded into the body of the card (and this is not necessary!).
Changing the quartz.
When the receiver is réallumer, it will work again.
solve the following:
1 º boot loader of the Mediabox website
2 º choose a door com.
3 º keep pushing on the pc control + c, and without the drop started the decoder, now
you:
access code?
enter "cafe" and enter,
Now you (sometimes takes a little ca)
boot_FORCE_ECP_1.6.a (DA3NED_VEN_V20.3)
BOOT_1.6.a>
Type "c" Enter and sends it, but then gets stuck on:
transfer flash_bfcf0000
turn off the decoder and then turn it back holding the two keys External
decoder, it appears t:
boot_LIBDAT_ECP_1.6.a (DA3NED_VEN_V20.3)
LOADING PRIORITY
FLASH ADR = bfc00000 M29W800B
FLASH ADR = a1200000 M29W800B
FLASH ADR = a1300000 (90.90) unrecognized
debut transfer parallele
Pending negotiation:
Nu verstuur I of a schrijft hij het correct:
key stop
End transfer parallele
checksum_flash = 0xa79a29c2
checksum_e2prom = 0x0000412d
!!!!! CUT CAN GIVE
!!!!! FOOD OF DECODER
now control + c, and off:
!!!!!! ABORT !!!!!!
RESET
* Bfc0.flash omgezet in bin file.
* Check cable and connected
* SRT8000 loader demarrer
* Receiver switch
* On the P.C. several times "Crtl + C"
* Access code? " su appears the P.C.
* Quickly introduce "cafe" (several times may be required)
no capital letters
* "Boot_FORCE_ECP_1.6.a (DA3NED_VEN_V20.3)
BOOT_1.6.a> "appears on the P.C.
* Type "c"
* Start "bfc0.bin"
* "Originele firmware erin" erin
* Kanalen laten zoeken in beeld!LLO THIS IS A GOOGLE TRADUCTION OF FIRST THREAD.