Plugin WLED Flash Tool Dreambox

[dreams@t]

WLED Flash Tool - Dreambox OE2.5/2.6, openATV, VTI

enigma2-plugin-extensions-wledflash_1.0.7-r0.0

WLEDFlashTool is a plugin with which you can easily flash an ESP8266 or ESP32 with the WLED software.WLED is a program with which you can control LED stripes for ambilight, lamps, decoration, events etc.
On enigma2 receivers especially suitable for Enigmalight and Hyperion.
Flashing and operation via USB, with Hyperion with the One operation also via WiFi.
Esptool.py is used for flashing.

Load and install the software packages suitable for your receiver.
Connect a Wemos D1 Mini, NodeMCU ESP8266 or ESP-32 board to USB.
Start the plugin, now you can select and release any release version of WLED in the plugin.
An update check is built in, so that you will be informed when there are new ones.
Save 'Custom Builds' in / media / hdd / WLED, these are then offered for flashing in the plugin.
Flash ESP8266, and bootloader for ESP32
Flash the xxx_ESP32xxx.bin to ESP32.
With 'RED' (reset) you can delete the flash.
If you experience problems, run this command before trying "write_flash" again.
(Note: This will delete all settings saved on the ESP!)
You can flash anything and at any time, settings are not lost.
Of course, if you flash a version that doesn't match the board or the stripes, nothing will light up.
In the file name of the release files you can clearly see for which board and for which stripe type the file is to be used.

If nothing is specified for the stripe type, WS2812b compatible stripes are to be used.
If the file name apa102 contains APA102 compatible stripes, etc.
If your stripe type is not available, you have to compile yourself.

The compatible chipsets for the color-coding are

1 pin:

WS2812B (5V)
WS2811 (12V power, with 5V signal)
WS2813 (WS2812 with redundant data on 2 wires DI and BI, to resist LEDs failure)
WS2815 (like WS2813 but 12V), send 5V signal on BI.

BTF2815 (cheaper 12V)
SK6813 (redundant like WS2813)
SK6812 (can support up to 4 colors, commonly GRBW)

SK6805 (3 colors)
2 pins (clock CI and data DI) chips:

APA102
SK9822
WS2801 (uses gpio0 and 2)
LPD8806
Beside the digital addressable LED stripes the good old analog LED stripes are supported, too:

4 pins: RGB
5 pins: RGBW / RGBWW / RGBCW / RGBNW (RGB + one white channel)
6 pins: RGBCT (RGB + 2 white channels)

The plugin is tested on Dreamboxes OE2.5 and 2.6 (arm64, armhf, mipsel).
WLED works with Hyperion and Enigmalight with USB everywhere, WiFi operation is only possible with Hyperion (One).
Installation:
Load packages depending on the box, unzip .zip. FTP the packages to / tmp on the box.
So you always need the plugin .deb and the appropriate .zip
Connect via telnet or ssh z. B. with putty

apt-get update
dpkg -i /tmp/*.deb
apt-get -f install

enter, the plugin, python and kernel modules will be installed.
After a successful installation (you can see if it was successful at the output in the console) restart the box the plugin WLED Flash Tool is now available.

[dreams@t]

enigma2-plugin-extensions-wledflash_1.0.8-r0.0

Changelog:
Revised parser for Wled.
wled_xxx.bin in / tmp is no longer deleted, the download can be used for 'Manual OTA Update' in the WLED WebUI if ESP is not connected via USB.
Support for plug-in assistance.

[Mafia_DZ]

08.06.2023

Update

enigma2-plugin-extensions-wledflash_1.1.0

-Adjustments WQHD and last italian translation by @ Spaeleus

[Mafia_DZ]

25.06.2023

Update esptool_3.0-r0.0_armhf.deb

--chip {auto,esp8266,esp32,esp32s2,esp32s3beta2 ,esp32c3}