[Plugin] CutlistEditor

[dreams@t]

CutlistEditor Alternative 2021

Installation:
* Uninstall the previous CutlistEditor (no matter whether from the feed or reloaded)
* Upload the IPK package (directory tmp or on HDD, I use Windows Explorer for this) and install it (in the VTI panel 'Manual installation of packages')
* Integrate the contained skin part into the skin you are using (works with the original, but special effects / information are lost)

MovieCut is fully integrated; the original version can, but does not have to be, uninstalled.
In addition to the familiar editing functions, a split function has also been implemented. Each block to be retained is output in a separate file, with only one CUT mark, both blocks.

All key assignments are displayed with the HELP key.

Compatibility:
Markers can also be set with the players. These are converted to the respective key frame at the start.
Cut markers from other cutlist editors are adopted with the unchanged position. These are not valid key frames and can therefore not be edited. However, a delete key (EPG / INFO) is defined for this. However, I recommend deleting all cut list entries if there are cut markers from other editors.

To all insiders:
The file Doku_for_Developers.txt describes how the key frames are determined. Unresolved problems are also listed there. Maybe someone already knows a solution.

To the (integrated) movie cut:
The executing file (mcut) is from the feed. This cuts a little unclean (at the transition points mostly images of the two frames that are next to each other after the cut are mixed).
In some cases, cutting blocks are lengthened, in extreme cases up to the end of the recording, so that the cut file can be larger than the original. The generated AP / SC files are the target files. A Reconstuct_APSC has to be carried out downstream here. This can also be set automatically in the settings.
I therefore recommend not to overwrite the originals.
Special candidates for these problems are recordings previously cut with MovieCut and decrypted ORF recordings.
And another hint: the editor is also UHD / 4k-capable
Key assignment: can be adjusted in keymap.xml. It should be noted, however, that no standard jump functions (seek) may be activated because these do not return the key frame positions of the jump target.

Thx @WeFraJo

[dreams@t]

CutlistEditor Alternative v3.0

The following adaptations were made in the attached version:
* The basic waiting time when executing between two jump functions (seekTo) has been increased by 25%
* In addition, when starting the editor, it can now be specified that positioning is at the beginning or the end of the recording (config.CLEA.START_POSITION)

Thx @WeFraJo

[dreams@t]

CutlistEditor Alternative v3.1

WeFraJo wrote
Changes:
* The cutting program (binary file mcut) cuts 1 - 3 frames before the selected one in certain situations. This is now intercepted as far as possible, but deviations can still occur with keyframes that are very close to one another
* When editing, if an error value is returned, its number is now also output. If this is undefined, the message now reads: "Possibly error when editing recording xxxx. Please check!"
1) is a correction to the message from Daretobi (thanks for testing!). This works for me without any problems, but not for him (with recordings of 6 - 8 hours in length). Therefore, ask for feedback as to whether and in what situation you have problems with it.

And again the note on the parameter config.CLEA.WAITTIME_ADJUST:
These work fine for me on the Duo 4k with 80 and on the SE with 150. In the event of unusual reactions to the jump buttons, please edit this value in the settings file and increase it until the buttons work correctly. A typical setting that is too low is that when you press the yellow button, the image jumps back to a previous position.

Don't forget: uninstall all versions of CutlistEditoren before installation (including the one from here)

Thx @WeFraJo

[ManInSpace]

Thanks for this plugin, but box get a blue screen. Box: Octagon SF8008 UHD with Pure2 6.5 based on OpenPLi. Any solution?