gamma up for show and art

[vamas]

I have again loaded another package and then went back to the 19th August file and both Show and Art work fine.
Pls have patience and try this file again. As I had said in page 2 sometimes one has to play about a bit and then have good results.
I can assure you that this file is working 101%

[Terminator1]

Hi vamas

I have progrmed my card with this file 19/18/08 for the last 6 days and I assure you I have only been able to open A*T. Could you tell me how you are progameing yours please. I am using Pheonix programer with Gamma loader v 1.1 and 6 mhz ticked.

Regards

[Terminator1]

Sorry file is 19/08/08

[Gaza]

I have again loaded another package and then went back to the 19th August file and both Show and Art work fine.
Pls have patience and try this file again. As I had said in page 2 sometimes one has to play about a bit and then have good results.
I can assure you that this file is working 101%

Iam in the same boat as Terminator 1 what do you mean by play about a bit what receiver or cam are you using

[vamas]

I am using cas 2 plud card loader and the 1.1 with 6mhz ticked, If art opens on this file so should showtime.
I am using matrix 1.80 as a cam and my reciever is a Golden Interstar,
by the way I just checked again to make sure it is still working and all is ok.

When i say play aroubnd, I meant like for example I leave on for about 1 hour then switch off reciever, take card out, turn on again and put card in again and most times it just come on after a couple of minute. When i does not I turn all off, go to bed as I mostly do this late evening and then check again the day after and up to now, keep my fingers crossed it has always come back.

[justmylcuk]

to vammas
which channel to you use for the update for showtime

[vamas]

I always use Show cinema 1 and for Art UKTV, now Granada.
By the way I cleaned card again yesterday ans re loaded and in about 5 minutes all opened up again. I did this just to try if all works OK again.

[Terminator1]

Hi Vamas

I have followed your instructions step by step. A*t opens strait away Sho**ime wont open. Could you upload the file you have please (if allowed)

Regards

[vamas]

I do not know how to attach file but I casn tell you that it was downloaded from Als.t .. uk

[djminato]

thanks alot all 4 share and I`ve a comment it may help

my gamma os1.4 was working art/show ok after programing mct it works then go back to 19-8 art/show still working after 2days re program mct then go back 19-8 using emk2 loader art ok show off till now no succeed to revive knowing that I`d used all gamma loaders with different method 3.57 and 6 but useless

one note: program you card with mct nova etc.. any of them then use any old version (2007-2008 ) of art/show.gam ART will go work knowing that gama erased many times well and used different loaders with old files ART will never go off

another thing after going showsport1 and waiting 10 min the sound of this channel can be listened for 5 seconds then off

I`d used different stb humax 5400, topfield 3200, eurocam 1.06 and going monitoring enable emm and enable ecm and autoupdate on also I`d tested freecam 2.018 also going to debug mode all the same

the fastest box in au is openbox x-600 knowing that I`d tested many boxes using multicas dreamsky 7000pvr . starsat 6000cu also 6300 super etc..

the question is ? is there any way to delete ART provider from 19-8.gam file