I have a question. I need some tuto for running server"CCcam" on my pc and CCcam/Newcs on dreambox like a client.
I have pc linux server with card reader and a dreambox witch i just watching there a tv. Also on dreambox i have a CCcam/newcs instaled and a card in there from newcamd server. How to make that all this ll work.
CCam on pc like server and CCcam/newcs on dreambox like client and also sharing a N line to my peers...
Thanks
You need to configure the CCcam.cfg files on both the PC and dreambox
and no the IP address of your PC server.
I am assuming you have a level of knowlege to FTP your PC and dreambox.
i.e open the file on your Linux Server var/etc/CCcam.cfg
Add the line
F: username password
Use a username and password of your choice.
Save the file
On your Dreambox
open the file var/etc/CCcam.cfg
and add the line
C: IP address of your PC server 12000 username password
Save the File
If CCcam is running on your Linux Server and dreambox you should sharing from your Linux Server to your dreambox
For your card reader connected to com port 1, on your Linux Server you also need to add the line to your CCcam.cfg File.
SERIAL READER : /dev/ttyS0 phoenix
If you want to over clock your card you also need to add the line
SMARTCARD CLOCK FREQUENCY: /dev/ttyS0 5300000
You may have to re-start your Linux Server
Good luck
with this configuration..it is possible to share my N line from dreambox??
do you want to use you dreambox as a newCS server and share to your :
Linux server then re-share from your linux server ???
nop
i want direct from my dreambox to my 5 peers who i give a N line?
my dreambox is only for watching and have newcs server...
No different setup
locate the file var/tuxbox/config/newcs.xml on your dreambox
it should look somthing like this and make the changes in bold for your clients this server will be listening to port 34000
if your clients are on a WAN and not a local network remember to forward port 34000 on your router to the ip addreass of your dreambox. and the IPaddress in your n lines will be your DYNDNS, NoIP address or external IP
<?xml version="1.0"?>
<!--
For setup-issues, look in readme.txt!
If there are other troubles, try different forums or irc channels around :o)
The configfile are NOT case-sensitive, and shouldnt care about dos/unix cr/lf.
** This is the example file for Dreambox/TD etc. that use SCI interfaces.
-->
<newCSconfig>
<readers name="Card Readers">
<device>
<name>lower</name>
<type>sci</type>
<mhz>500</mhz>
<node>/dev/sci0</node>
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<!-- <rsa>0000000000</rsa> -->
<irdeto-camkey>0000000000000000</irdeto-camkey>
<irdeto-camkey-data>00000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 000000000000000000000</irdeto-camkey-data>
<crypto-special>No</crypto-special>
<ipk>00000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 000000000000000000000</ipk>
<ucpk>0000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000000000000000000000 0000000000000000000000</ucpk>
<PTShandshake>No</PTShandshake>
<carddetect>yes</carddetect>
<newcamd_port>34000</newcamd_port>
<autosid>Yes</autosid>
<Seca-PPV>no</Seca-PPV>
<pincode>0000</pincode>
<priority>round</priority>
</device>
</readers>
<radegastserver>
<enabled>No</enabled>
<port>16000</port>
<allow>
<hostname>localhost</hostname>
</allow>
</radegastserver>
<cache>
<emm>20</emm>
<ecm>-1</ecm>
</cache>
<httpd>
<server> <!-- Port to accept connections on -->
<port>8080</port>
<enabled>no</enabled>
</server>
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for browser to logon (its case sensitive). -->
<name>username</name>
<!-- valid value for password are:
Any password you'd like - Used for browser to logon (its case sensitive). -->
<password>password</password>
<!-- valid value for accesslevel are:
admin, stats - Define what rights the user has in the web-console -->
<accesslevel>admin</accesslevel>
</user>
</httpd>
<debug>
<password>password</password>
<level>normal</level>
<type>init</type>
<output>console,tcp</output>
<console_options>normal,init</console_options>
<tcp_port>1001</tcp_port>
<tcp_options>normal,init</tcp_options>
</debug>
<newcamdserver>
<enabled>Yes</enabled>
<name>newcs</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<user>
<name>client1</name>
<password>password1</password>
<hostname>localhost</hostname>
<port>34000</port>
<au>on</au>
<sidoverride>on</sidoverride>
<spider>yes</spider>
<rate>2</rate>
</user>
<user>
<name>client2</name>
<password>password2</password>
<hostname>localhost</hostname>
<port>34000</port>
<au>on</au>
<sidoverride>on</sidoverride>
<spider>yes</spider>
<rate>2</rate>
</user>
<user>
<name>client3</name>
<password>password3</password>
<hostname>localhost</hostname>
<port>34000</port>
<au>on</au>
<sidoverride>off</sidoverride>
<spider>No</spider>
<rate>2</rate>
</user>
<user>
<name>Client4</name>
<password>password4</password>
<hostname>localhost</hostname>
<port>34000</port>
<au>on</au>
<sidoverride>off</sidoverride>
<spider>No</spider>
<rate>2</rate>
</user>
<user>
<name>client5</name>
<password>password5</password>
<hostname>localhost</hostname>
<port>12000</port>
<au>on</au>
<sidoverride>off</sidoverride>
<spider>No</spider>
<rate>2</rate>
</user>
</newcamdserver>
</newCSconfig>
then the N lines you give to your clients for them to insert into there cccam.cfg files should look like this
N: IPaddress 34000 client1 password1 01 02 03 04 05 06 07 08 09 10 11 12 13 14
etc etc
What did you want the linux server for ???
Regards
i have all this before that u wrote, but i m offline with my newcamd server
before that i was having a server on dreambox it s works
but now is not working
it s works now
Not to sound like a total retard, but if i use a PC as the server does it need to contain a DVB-S reciever for card auth? or do the slave handle this themselfs?
only reason im asking is cause when i use my DM7020 as a server and my DM100 as slave the 7020 needs to have Sat connection inorder to slave the keys using CCCam to the DM100 (only running CCCam)
Also im currently using swedish Canaldigital but i was thinking of getting a Viasat subscription but i was wondering if i need anything more then the BoxID to make it work ? most Guides/Tutorials mention the DESKEY but there dont seem to explain anywhere is this is a made up one or if i need to extract it somehow from my card ?
And finaly is there someway to extract my Subscriber cards to Software (read the keys and use them as files instead?) ive found something called niagraedit but im unsure if this will allow me to extract the data needed or even if this is possible nowdays?
No PC server works fine without sat connections your only sharing the emm and emu's not the sat feeds.
You just need to configure CCcam to update the card emu using one remote client that has a sat connection.
I use a Debian CCcam server with card reader only. A DM500 on my local network is configured to update the card by allowing EMU updates this is normal by default so
F: client password
C: serverIP port client password yes
should work but you can add { 2:1:1 } at the end of one F: Line to make sure and all others end with { 2:0:0 } otherwise your card will be updated from everyone that shares.
Thank you for the info
that leaved me with some questions mark about the
DESKEY and downloading of my subscriber card to file AU ? (i believe its called something close to it?)
Posting Permissions
Reply With Quote