hello,
I am with someone try make a firmware to be able to hang the reciver to gbox and share over sssp . gbox works but give error on sssp. the maker says that the reciver the correct information not sent to gbox. now the question was. which information must the reciver V correctly to gbox? who can help us???
greetz
SSSP – Simple Serial Sharing Protocol
=====================================
This Protocol defines the communication between a DVB Box and a gbox by using a RS232(serial/com/tty port) with only 4 commands to implement.
RS232 communication settings
============================
115200 8N1 (115200 Baud, 8 data bits, no parity, 1 stop bit)
To activate add in the gbox_cfg R: { 01 } for com1, or R: { 02 } for com2
W: and V: should be deactivated 00 00
When developing Software you can activate thers232 debug messages by adding
10 to the R: parameter, a example for com1 would be R: { 11 }
Format of data
==============
AB CD EF GH ....
AB = Command
CDEF = length of the data following
GH ... = data
Total length is CDEF + 3 (1 byte command + 2 bytes len)
Command 0x means from STB to gbox
Command Fx means from gbox to STB
SEND PMT = 01 (send PMT to gbox)
--------------------------------
01 xx xx yy yy zz zz zz zz data ....
xx = Len
yy = SID ( byte 2 and bytes 3 from the PMT)
zz = PMT CRC32 (last 4 bytes in the PMT)
Data = CAID1 (2 bytes) PID1 (2 bytes) PROVIDER1 (3 bytes) CAID2 PID2 PROVIDER2 ....
Provider is only used in Seca and Viaccess, in other systems put 00 00 00
For Seca use 00 xx yy and for viaccess xx yy z0
On each channel change the DVB box must send the PMT first, on FTA Channels please send: 01 00 06 yy yy zz zz zz zz
SEND ECM = 03 (send ECM to gbox)
--------------------------------
03 xx xx yy yy ecm_data ....
xx = len
yy = pid
Note: Please send every ecm only once, do not send the same ecm multiple times.
REQUESTING PIDS DATA = F1 (receive ECM pid list )
-------------------------------------------------
F1 xx xx pid1 pid2 pid3 ....
xx = Len
pidx = 2 bytes for each pid
Please send me ECM data from these pids only, close all other already open.
CW RETURN = F2 (receive ControlWords)
-------------------------------------
F2 00 10 cw1 (8 bytes) cw2 (8 bytes)
Command flow on a channel change
================================
1. DVB box sends PMT with command 01 on a channel change
2. gbox sends pid list of the ecm's it can handle with command F1
3. DVB box sends ECM's (from all pids in the pid list) with command 03
4. gbox sends CW's with command F2
5. As soon the gbox has success in decoding a ecm it sends again a F1 command
with one pid only, the DVB box should close then all other pids and from
now on send only ecm data from that pid.
After this command 03 and F2 will be repeated until a channel change.
On the next channel change the DVB should close all open pids and repeat the
above procedure.
hi, were comming the good way.
now we get for a moment picture.
2 ECM's en than go is on black.
what are we doing wrong???
greetz
Difficult to say with allllllOriginally Posted by Didden
the information you send here.....
Can you put a log of all SSSP messages here?
Very interesting stuf you are doing. Can you tel more about which receiver? I am also writing something.
yes we got picture on c+nl en d+ spain.
looking good.
this is for a philips reciver 6071 and 6072
i will ask for a log
greetz
tvv works - c+nl works - d+ sometime - and the deltacrypt VH1 ....
the rest dont work. why we dont know
greetz
Very intersting discussion.
(i have a problem with gbox fte....)
what is cpu of philips?
sti?
tnx
hi,
sti5512
greetz
Hmmm. Strange.
Do you have the SSSP log already? Specialy the part which shows a working and not working d:.
OK!
So cpu is like sumsung 9500.
I have a good serial port source for this box!.(with gbox and dongle y4
)
(gbox should add in serial port section)
Posting Permissions
Reply With Quote