Gamma card not Atr Help

[CCcam.2008]

Hi All
My Gamma card appears to be dead, I recently updated it with nova file and it worked for 2 days but not anymore, in my technomate 6900 super it says invalid card, so I was looking for an older file to reload that, if I put the gamma card in the cas3 programmer and it says no atr.
anyone any ideas
regards

[kapazita]

Check that you have chosen correct COM port.

[CCcam.2008]

no com port no phoenix problem b/c i have aouther card show atr i try atr kit but 5 day still waiting

[stergiost3]

no atr to me what i do??????

[juliani69]

no atr to me what i do??????

use sataid loader with any file. after 20 min your card will be ok !

[CCcam.2008]

i try more time problem stil

[powervolume]

hi did you repair your card
i have the same problem

[satleonhh]

Mostly if emergency Atr error message comes, then one selected wrong Comport or the cable is not attached. The error message comes even if the map not in that subject lies.

[moi]

Mostly if emergency Atr error message comes, then one selected wrong Comport or the cable is not attached. The error message comes even if the map not in that subject lies.

Can you follow the instructions I hope it will be ok Open Sataid Team GammaLoader and load your gam file
Then reset the card with emk & check the atr
good luck be patient

http://www.sendspace.com/file/gvj939

[moi]

I have found this is not from me it's copy paste

English:

If a gamma card displays showing errors such as incorrect or no ATR or ATR, the ATR does not appear try the following steps to find out whether or funzt.

the first thing we should know what ATR is an "empty" AT90SC7272C atmel smartcard (the smartcard, the type of the gamma benόtzt)

ATR an empty Atmel AT90SC7272C
3B 7F 11 00 00 00 6B 1A 0E 06 4b16 36 23 09 11 03 05 90 00

1A corresponds to the 7272c chip type (and not the 3232C, or 6464c)

0E 06 4b16 36 23 09 11 the serial number corresponds to the smartcard
0305 corresponds to the version of the boot-loaders
90 00 is the map showing the unwritten

smartcards (AT90SC7272c atmel processor) programmed with the operating system of the gamma-have team:


ATR Gamma Card V1.4
3B 9F 21 0E 47 41 4D 4D 41 43 41 52 44 20 56 20 31 2E 34 9D

that is, if we ****** simulate (that is, if we miss alters the map, a new gammafile) is also in the ATR:

ATR ****** ACS V4.1
3B 9F 21 0E 49 52 44 45 54 4F 20 41 43 53 20 56 34 2E 31 9D

In the newer version ****** we have:

ATR ****** ACS V5.0
3B 9F 21 0E 49 52 44 45 54 4F 20 41 43 53 20 56 35 2E 30 9D

ATR ****** ACS V5.3
3B 9F 21 0E 49 52 44 45 54 4F 20 41 43 53 20 56 35 2E 33 9E

ATR ****** ACS V5.4
3B 9F 21 0E 49 52 44 45 54 4F 20 41 43 53 20 56 35 2E 34 99

if the card is blocked then the ATR ends in 6983 or 69 89

I think that in most fδllen with the ATR problem is not the operating system of the gamma Broken
but only a question of communication between the PC and the programmers.

on what we mόssen eight by the gamma used correctly:

1) the cable with which we connect the PC and the programmer must have a RS323 MF be (not the cable that we at the receiver and PC benόtzen)

2) the serial port (COM port) of the gerδte-manager is engestellt must be the same as the programmer with the

3) if the programmer has no direct serial connection and we got a usb adapter to serial benόtzen we absolutely need the drivers.

4) how mόssen to abide by the programmer geanu get the correct voltage it needs.

5) a very important topic which is the operating system and processor speed benόtzen (a Q6600 Vista64 SP1, the loader does not funz EMF 3.5, a somewhat δlteren PC with WINXP SP3 lδufts and easily.
the new software by Duolabs CAS3 "CAS Studio 8.6c" is, in my opinion the best software to read the gamma or describe.

Several users reported reading the card in a gamma with various programs, the announcement was awarded as "bad or no ATR ATR".
The advantage of CAS3 is in no serial cable needed but only a USB.
natόrlich if we have a software benόtzen except the CAS Studio mόssen then we also connect a serial cable and set the option MHz.

6) is also one of the most important things that we read the card, the kφnnen gamma MHz option correctly set.
the ATR (Answer To Reset) is the first contact between the operating system of the gamma card and programmer,
that is, if we do not have the setting Richtg MHz as obtained from the manufacturer then we get the message "bad or no ATR ATR which means that the map is broken"

7) so that we read the gamma kφnnen we should benόtzen a phoenix programmer 6 MHz
(programmer natόrlich gehts with other but I think Phoenix is the Best Positions for the gamma).

if we want that the CAS3 funzt with EMK3.5 we benόtzen the Phoenix 6 MHz mode and combine it with a serial cable.
(and to pay attention to the COM port that we benόtzen is the same as in the EMF 3.5.

__________________