Gammacard_Update_Nova_200 81130

[mxantho]

the same file....
++ Date : 10/2/2009 (at 12:46:15 ðì)
++ Ascii Serial : 4012 3456 788
++ Hex Serial : 07 B3 98
++ ProviderID-00 : 03 EC D1
++ Date-00 : 0A 16
++ ProviderID-10 : 09 8C D1
++ Date-10 : 0D 00

working
any ideas???

It is the first time I see a 2009 gam file! I haven't seen it in here..

[sathack69]

this they is the date that I wrote the 2 cards. .there are however differences between them, even if they have the same file.thats the problem with the cards...

[qwerty12]

the same file....
++ Date : 10/2/2009 (at 12:46:15 ðì)
++ Ascii Serial : 4012 3456 788
++ Hex Serial : 07 B3 98
++ ProviderID-00 : 03 EC D1
++ Date-00 : 0A 16
++ ProviderID-10 : 09 8C D1
++ Date-10 : 0D 00

working

++ Date : 10/2/2009 (at 12:35:40 ðì)
++ Ascii Serial : 4012 3456 788
++ Hex Serial : 07 BA 58
++ ProviderID-00 : 03 EF CF
++ Date-00 : FF FF
++ ProviderID-10 : 09 8F 3D
++ Date-10 : 0D 00

not working...

any ideas???

As I see, the same .gam file does not work the first time you program it into the card. But the second time works. I assume that this happens because MAYBE some bytes remain into the card even if you clear it and write the new file. Maybe a solution is to clear it twice and write the .gam file as many times as needed until it works. But I am not really sure about it...

Any other solutions and explanations why the gamma cards do not work? N**a changed their systems?

[fr2er]

As I see, the same .gam file does not work the first time you program it into the card. But the second time works. I assume that this happens because MAYBE some bytes remain into the card even if you clear it and write the new file. Maybe a solution is to clear it twice and write the .gam file as many times as needed until it works. But I am not really sure about it...

Any other solutions and explanations why the gamma cards do not work? N**a changed their systems?

Which file did you upload?

[qwerty12]

yes, sathak69 which file did you upload?

[djminato]

please try these steps it may help you

1- use emk3.1 press reset then clean card
2- press load os and select the attached os.bin file
3- send file when finished
4- remove card from programmer then insert it back
5- use gammaloader 1.1 and load attached 17-11
6- press program after complition press program again
7- now go to novacinema1 and wait at max 1 min it will open
8- use emk3.1 press reset ( Don`t clean )
9- load attached gam 30-11 then send to card
10- go novacinema1 CY also wait max 1 min and it will open

if not open then you have to do factory reset to your box then search channels again now do a test

note: use 6 mhz in all steps

my working card details after all above steps is:

[sathack69]

one card worked again with 3/4/08 file...after 3 hours and reset again...i will try with another and tell you..

[ceyer]

Hi,

just a quick one:

What is emk3.1??? & where do I get it??

thanks

edit:

It´s here: http://www.satsupreme.com/showthread.php?t=57168

[humidream]

Use the emk 3.1 but not work, I see message 'Componet COMDLG32.OCX or one of its dependencies not correctly registered a file is missing or invalid'. Why? Please help...

[michael318]

you need this!!

http://www.satsupreme.com/attachment...2&d=1234462893